SFI SYSTEM > VC Output Circuit |



| 1.CHECK MIL CONDITION |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
| Communication is possible | A |
| Communication is not possible | B |
|
| ||||
| B | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the throttle body assembly connector.
|
| ||||
| B | |
| 4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the accelerator pedal position sensor connector.
|
| ||||
| B | |
| 5.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)) |
Disconnect the camshaft position sensor (for intake side) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the camshaft position sensor (for intake side) connector.
|
| ||||
| B | |
| 6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)) |
Disconnect the camshaft position sensor (for exhaust side) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the camshaft position sensor (for exhaust side) connector.
|
| ||||
| B | |
| 7.CHECK MIL (VACUUM SENSOR) |
Disconnect the vacuum sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the vacuum sensor connector.
|
| ||||
| B | |
| 8.CHECK MIL (BATTERY CURRENT SENSOR) |
Disconnect the battery current sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the battery current sensor connector.
|
| ||||
| B | |
| 9.CHECK MIL (OIL PRESSURE SENSOR) |
Disconnect the oil pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the oil pressure sensor connector.
|
| ||||
| B | |
| 10.CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the vacuum sensor connector.
Disconnect the battery current sensor connector.
Disconnect the oil pressure sensor connector.
![]() |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-89 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A12-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A12-58 (VCP2) - Body ground | Always | 10 kΩ or higher |
| B32-119 (VCV1) - Body ground | Always | 10 kΩ or higher |
| B32-121 (VCE1) - Body ground | Always | 10 kΩ or higher |
| B32-67 (VCPM) - Body ground | Always | 10 kΩ or higher |
| B32-95 (VCPT) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to ECM) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the throttle body assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the camshaft position sensor (for intake camshaft) connector.
Reconnect the camshaft position sensor (for exhaust camshaft) connector.
Reconnect the vacuum sensor connector.
Reconnect the battery current sensor connector.
Reconnect the oil pressure sensor connector.
Reconnect the ECM connectors.
|
| ||||
| OK | ||
| ||