DTC P0500 Vehicle Speed Sensor "A" |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While the vehicle is being driven, no vehicle speed sensor signal is sent to the ECM. (1 trip detection logic: for CVT) (2 trip detection logic: for manual transaxle) |
|

| 1.CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER) |
![]() |
Disconnect the ECM connector.
Disconnect the combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) - A12-38 (SPD) | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Combination Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
Reconnect the combination meter connector.
|
| ||||
| OK | |
| 4.CHECK COMBINATION METER (+S VOLTAGE) |
![]() |
Disconnect the combination meter connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| * | Front view of wire harness connector (to Combination Meter) |
|
| ||||
| OK | |
| 5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM) |
![]() |
Remove the combination meter assembly.
Connect the combination meter connector.
Move the shift lever to the neutral position.
Jack up one of the rear wheels.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.
| Tester Connection | Condition | Specified Condition |
| E22-39 (+S) - Body ground | Ignition switch ON Turn wheel slowly | Voltage generated intermittently |
| * | Component with harness connected (Combination Meter) |
|
| ||||
| OK | ||
| ||
| 6.CHECK COMBINATION METER (SPD SIGNAL INPUT WAVEFORM) |
![]() |
Remove the combination meter assembly.
Connect the combination meter connector.
Move the shift lever to the neutral position.
Jack up one of the rear wheels.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) - Body ground | Ignition switch ON Turn wheel slowly | Voltage generated intermittently |
| * | Component with harness connected (Combination Meter) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR ASSEMBLY) |
Disconnect the combination meter connector.
Disconnect the brake actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-38 (SI) - A67-11 (SP1) | Always | Below 1 Ω |
| E22-38 (SI) or A67-11 (SP1) - Body ground | Always | 10 kΩ or higher |
Reconnect the combination meter connector.
|
| ||||
| OK | ||
| ||