Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  


DESCRIPTION

The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0365 Camshaft Position Sensor "B" Circuit (Bank 1) No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for exhaust camshaft)

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for exhaust camshaft)

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for exhaust camshaft)

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies

HINT:

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0340


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor for exhaust camshaft despite the camshaft revolving, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Related DTCs P0365: Exhaust camshaft position sensor verify pulse input
P0367: Exhaust camshaft position sensor range check (low voltage)
P0368: Exhaust camshaft position sensor range check (high voltage)
Required Sensors/Components (Main) Exhaust camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous
Duration 5 seconds: P0365
4 seconds: P0367, P0368
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None

P0365: Exhaust Camshaft Position Sensor Verify Pulse Input
All of the following conditions are met -
Engine speed 600 rpm or higher
Exhaust camshaft position sensor range check fail (P0367, P0368) Not detected
Ignition switch ON
Starter Off
Battery voltage 8 V or higher
Exhaust camshaft position sensor voltage 0.3 to 4.7 V

P0367 and P0368: Exhaust Camshaft Position Sensor Range Check
All of the following conditions are met -
Starter Off
Ignition switch ON
Time after ignition switch turned from off to ON 2 seconds or more
Exhaust camshaft position sensor verify pulse input fail (P0365) Not detected
Battery voltage 8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

P0365: Exhaust Camshaft Position Sensor Verify Pulse Input
Exhaust camshaft position signal No signal

P0367: Exhaust Camshaft Position Sensor Range Check (Low Voltage)
Exhaust camshaft position sensor voltage Less than 0.3 V

P0368: Exhaust Camshaft Position Sensor Range Check (High Voltage)
Exhaust camshaft position sensor voltage Higher than 4.7 V

COMPONENT OPERATING RANGE

Exhaust camshaft position sensor voltage 0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0365, P0367 or P0368.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A255253
1.083,1.927 1.354,2.073 0.271,0.146 10 B41 1.083,2.094 4.281,2.292 3.198,0.198 10 Camshaft Position Sensor (for Exhaust Camshaft) 5.177,0.427 5.573,0.573 0.396,0.146 10 VCE1 5.177,0.969 5.563,1.125 0.385,0.156 10 EV1+ 5.177,1.5 5.604,1.656 0.427,0.156 10 EV1- 5.708,2.198 6.031,2.375 0.323,0.177 10 B77 5.708,2.365 6.052,2.552 0.344,0.188 10 ECM 4.844,0.417 5.115,0.604 0.271,0.188 10 111 4.906,0.958 5.115,1.156 0.208,0.198 10 81 4.844,1.5 5.094,1.667 0.25,0.167 10 112 2.646,0.427 2.771,0.594 0.125,0.167 10 3 2.646,0.958 2.75,1.135 0.104,0.177 10 1 2.646,1.5 2.75,1.646 0.104,0.146 10 2 2.25,0.427 2.542,0.604 0.292,0.177 10 VC2 2.177,0.958 2.594,1.125 0.417,0.167 10 VVE+ 2.198,1.49 2.615,1.656 0.417,0.167 10 VVE- 1.615,0.896 1.75,1.063 0.135,0.167 10 * 0.073,2.396 4.406,2.583 4.333,0.188 10 *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
a.
A194108
0.365,2.302 0.823,2.583 0.458,0.281 2.01,2.51 2.292,3.073 false 0.208,0.198 0.396,0.375 0.188,0.177 10 *a 0.458,2.354 0.844,2.573 0.385,0.219 10 B41 2.219,3.104 2.646,3.323 0.427,0.219 10 VC2
*a Front view of wire harness connector
(to Camshaft Position Sensor for Exhaust Camshaft)


Disconnect the camshaft position sensor for exhaust camshaft connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B41-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor for exhaust camshaft connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B41-1 (VVE+) - B77-81 (EV1+) Always Below 1 Ω
B41-2 (VVE-) - B77-112 (EV1-) Always Below 1 Ω
B41-1 (VVE+) or B77-81 (EV1+) - Body ground Always 10 kΩ or higher
B41-2 (VVE-) or B77-112 (EV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
a.
B319222
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the camshaft position sensor for exhaust camshaft installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

6.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
a.

Replace the camshaft position sensor (for exhaust camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the Techstream on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0365, P0367 or P0368 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor for exhaust camshaft connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B41-3 (VC2) - B77-111 (VCE1) Always Below 1 Ω
B41-3 (VC2) or B77-111 (VCE1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR