Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR(for 2WD)
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0057935 REAR SPEED SENSOR(for 2WD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (SKID CONTROL SENSOR)

Hide 2.INSTALL REAR DISC

Hide 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

Hide 4.INSTALL SKID CONTROL SENSOR WIRE

NOTICE:

To prevent interference with other parts, do not twist the painted line areas of the sensor wire when installing it.


a.
C278577
1.083,2.323 0.958,3.063 0.958,3.063 0.833,3.063 false 0.635,2.969 0.813,3.167 0.177,0.198 10 *a 1.344,2.042 1.5,2.24 0.156,0.198 10 A 2.865,1.792 3.021,1.99 0.156,0.198 10 B 2.833,2.479 2.99,2.677 0.156,0.198 10 C
*a Painted Line


Connect the skid control sensor wire connector labeled A to the skid control sensor.


b.

Install the sensor clamp labeled B with the bolt labeled C.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamp.



c.
C278576
1.979,2.073 2.156,1.875 2.156,1.875 2.563,1.875 false 1.427,1.531 1.146,1.115 1.146,1.115 0.979,1.115 false 0.781,1.031 0.958,1.208 0.177,0.177 10 *a 0.438,2.375 0.594,2.573 0.156,0.198 10 D 1.25,2.885 1.406,3.083 0.156,0.198 10 E 2.125,0.594 2.281,0.792 0.156,0.198 10 F 3.031,0.448 3.188,0.646 0.156,0.198 10 G 2.615,2.375 2.771,2.573 0.156,0.198 10 E 1.771,2.625 1.927,2.823 0.156,0.198 10 D 2.594,1.792 2.771,1.969 0.177,0.177 10 *a
*a Painted Line


Install the sensor clamps labeled D with the 2 nuts labeled E.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamps.



d.

Install the sensor clamp labeled F with the bolt labeled G.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamp.



e.
C279263
0.958,1.719 0.958,2.688 false 2.5,2 2.5,2.708 2.5,2.708 2.74,2.708 false 1.792,1.458 2.219,1.094 2.219,1.094 2.49,1.094 false 2.542,1.031 2.781,1.188 0.24,0.156 10 *1 2.781,2.635 2.99,2.813 0.208,0.177 10 *2 0.906,2.74 1.094,2.917 0.188,0.177 10 *3 1.781,0.375 2.094,0.531 0.313,0.156 10 *a
*1 Grommet
*2 Connector
*3 Band Clamp
*a Inside of Vehicle


Insert the connector and grommet into the inside of the vehicle through the passage hole in the wheel house.

NOTICE:

Make sure the grommet band clamp remains on the outside of the vehicle.



f.

Hold the grommet and pull it toward the outside of the vehicle. Then fix the grommet in place so that it is not tilted.

C274704
1.573,0.573 1.74,0.771 0.167,0.198 10 *a 4.771,2.24 4.938,2.427 0.167,0.188 10 *b 5.427,2.229 5.594,2.417 0.167,0.188 10 *b
*a Outside of Vehicle *b 30°


NOTICE:
·

When pulling out the grommet, do not grip the sensor wire.

·

Fix the grommet in place within the range shown in the illustration.




g.

Connect the skid control sensor wire connector.


Hide 5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Install the deck trim side panel LH (Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).

HINT:

Refer to the procedures from the installation of the deck trim side panel LH up until the installation of the rear door scuff plate LH.



Hide 6.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)