Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1413  Front Speed Sensor RH Output Malfunction  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1271, C1272, C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271

DTC No. Detection Item DTC Detection Condition Trouble Area
C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH

·

Front speed sensor rotor RH (Front axle hub sub-assembly RH)


C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor LH

·

Front speed sensor rotor LH (Front axle hub sub-assembly LH)


C1413 Front Speed Sensor RH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH

·

Front speed sensor circuit

·

Front speed sensor rotor RH (Front axle hub sub-assembly RH)

·

Skid control ECU (Brake actuator assembly)


C1414 Front Speed Sensor LH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Front speed sensor circuit

·

Front speed sensor rotor LH (Front axle hub sub-assembly LH)

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1413 and C1275 are for the front speed sensor RH.

·

DTC C1414 and C1276 are for the front speed sensor LH.



WIRING DIAGRAM

Refer to DTCs C1271, C1272, C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRAC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


e.

According to the display on the Techstream, read the Data List.


Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRAC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2
f.

Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Chassis > ABS/VSC/TRAC > Utility
Tester Display
Signal Check
50005 105 1003
OK:

All Test Mode DTCs are cleared.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output



DTCs C1413 and C1414 are not output

DTCs C1413 and/or C1414 are output

11.REPLACE FRONT SPEED SENSOR
5.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT SPEED SENSOR TIP

NG

6.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

7.INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.INSPECT FRONT SPEED SENSOR ROTOR
a.

Remove the front axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

·

If the speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.




c.

Reinstall the front speed sensor and the front axle hub sub-assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION for the front speed sensor

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION for the front axle hub sub-assembly


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector and the A14 and/or A43 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A64-7 (FR+) - A43-1 (FR+) Always Below 1 Ω
A64-6 (FR-) - A43-2 (FR-) Always Below 1 Ω
A64-7 (FR+) or A43-1(FR+) - Body ground Always 10 kΩ or higher
A64-6 (FR-) or A43-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A64-19 (FL+) - A14-1 (FL+) Always Below 1 Ω
A64-18 (FL-) - A14-2 (FL-) Always Below 1 Ω
A64-19 (FL+) or A14-1 (FL+) - Body ground Always 10 kΩ or higher
A64-18 (FL-) or A14-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.
C271648
0.906,0.448 1.292,0.719 0.385,0.271 2.208,0.469 2.625,0.729 0.417,0.26 1.198,1.844 1.135,1.427 false 2.385,1.833 2.51,1.427 false 0,0 0.313,0.156 0.313,0.156 10 false *a 0.99,0.49 1.448,0.688 0.458,0.198 10 false A43 2.26,0.49 2.719,0.688 0.458,0.198 10 false A14 1.135,1.896 1.594,2.094 0.458,0.198 10 false FR+ 2.271,1.906 2.729,2.104 0.458,0.198 10 false FL+ 1.021,0.219 1.333,0.417 0.313,0.198 10 false *A 2.354,0.198 2.667,0.396 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A43-1 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A14-1 (FL+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

10.RECONFIRM DTC
a.

Reconnect the A14 and/or A43 front speed sensor connector.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTCs C1413 and/or C1414 are output
DTCs C1413 and C1414 are not output



DTCs C1413 and/or C1414 are output

11.REPLACE FRONT SPEED SENSOR

DTCs C1413 and C1414 are not output

11.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Result:
Proceed to
NEXT



NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output



DTCs C1413 and C1414 are not output

END

DTCs C1413 and/or C1414 are output

13.REPLACE FRONT AXLE HUB SUB-ASSEMBLY
13.REPLACE FRONT AXLE HUB SUB-ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (front axle hub sub-assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
NEXT



NEXT

14.RECONFIRM DTC
14.RECONFIRM DTC

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output



DTCs C1413 and C1414 are not output

END

DTCs C1413 and/or C1414 are output