Refer to DTCs C1273, C1274, C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1407 | Open or Short in Rear Speed Sensor RH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH (for AWD) ·
Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD) ·
Skid control sensor wire RH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
| C1408 | Open or Short in Rear Speed Sensor LH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor LH (for AWD) ·
Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD) ·
Skid control sensor wire LH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
Refer to DTCs C1273, C1274, C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited (for 2WD).
Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | Rear speed sensor RH open detection | Normal or Error | Normal | Error: Momentary interruption |
| RL Speed Open | Rear speed sensor LH open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| RR Speed Open |
| RL Speed Open |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG (for 2WD) |
| NG (for AWD) |
OK
NG (for 2WD)
NG (for AWD)
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed:
No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed:
No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
| RL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG (for 2WD) |
| NG (for AWD) |
OK
NG (for 2WD)
NG (for AWD)
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| DTCs C1407 and C1408 are not output |
| DTCs C1407 and/or C1408 are output |
DTCs C1407 and C1408 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs C1407 and/or C1408 are output
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
for RH:
Disconnect the m1 and mM1 skid control sensor wire connectors.
for LH:
Disconnect the n1 and nN1 skid control sensor wire connectors.
| *A | RH |
| *B | LH |
| *a | Front view of Skid Control Sensor Wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-2 (+) - mM1-1 | Always | Below 1 Ω |
| m1-1 (-) - mM1-2 | Always | Below 1 Ω |
| m1-2 (+) - mM1-2 | Always | 10 kΩ or higher |
| m1-2 (+) or mM1-1 - Body ground | Always | 10 kΩ or higher |
| m1-1 (-) - mM1-1 | Always | 10 kΩ or higher |
| m1-1(-) or mM1-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-2 (+) - nN1-1 | Always | Below 1 Ω |
| n1-1 (-) - nN1-2 | Always | Below 1 Ω |
| n1-2 (+) - nN1-2 | Always | 10 kΩ or higher |
| n1-2 (+) or nN1-1 - Body ground | Always | 10 kΩ or higher |
| n1-1 (-) - nN1-1 | Always | 10 kΩ or higher |
| n1-1 (-) or nN1-2 - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD:
Reconnect the mM1 (for RH) or nN1 (for LH) skid control sensor wire connector.
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A64 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-17 (RR+) - m1-2 (+) | Always | Below 1 Ω |
| A64-16 (RR-) - m1-1 (-) | Always | Below 1 Ω |
| A64-17 (RR+) or m1-2(+) - Body ground | Always | 10 kΩ or higher |
| A64-16 (RR-) or m1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-5 (RL+) - n1-2 (+) | Always | Below 1 Ω |
| A64-4 (RL-) - n1-1 (-) | Always | Below 1 Ω |
| A64-5 (RL+) or n1-2 (+) - Body ground | Always | 10 kΩ or higher |
| A64-4 (RL-) or n1-1 (-) - Body ground | Always | 10 kΩ or higher |
for AWD:
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A64 skid control ECU (brake actuator assembly) connector and the N11 and/or M20 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-17 (RR+) - M20-1 (RR+) | Always | Below 1 Ω |
| A64-16 (RR-) - M20-2 (RR-) | Always | Below 1 Ω |
| A64-17 (RR+) or M20-1(RR+) - Body ground | Always | 10 kΩ or higher |
| A64-16 (RR-) or M20-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-5 (RL+) - N11-1 (RL+) | Always | Below 1 Ω |
| A64-4 (RL-) - N11-2 (RL-) | Always | Below 1 Ω |
| A64-5 (RL+) or N11-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| A64-4 (RL-) or N11-2 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD:
Reconnect the A64 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| m1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| n1-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
for AWD:
Reconnect the A64 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M20-1 (RR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N11-1 (RL+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK (for 2WD) |
| OK (for AWD) |
| NG |
OK (for 2WD)
OK (for AWD)
NG