Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

Refer to DTCs C1281, C1421, C1423 and C1424.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1281

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more while the vehicle is being driven at a speed of 3 km/h (2 mph) or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)

·

Brake actuator assembly (Master cylinder pressure sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Check the DTC C1425 is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1425 is not output
DTCs C1422 and C1425 are output




DTC C1425 is not output

2.READ VALUE USING TECHSTREAM (STOP LIGHT SW, MASTER CYLINDER SENSOR)

DTCs C1422 and C1425 are output

2.READ VALUE USING TECHSTREAM (STOP LIGHT SW, MASTER CYLINDER SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


e.

In accordance with the display on the Techstream, read the Data List.


Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0 V, Max.: 5 V Brake pedal released: 0.3 to 0.9 V Reading increases when brake pedal is depressed.
Chassis > ABS/VSC/TRAC > Data List
Tester Display
Stop Light SW
Master Cylinder Sensor
50003 105 37,9
Standard Voltage:

Master cylinder pressure sensor reading is 0.86 V or less at the instant the stop light switch changes from off to on.


Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.RECONFIRM DTC

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1422 is not output
DTC C1422 is output



DTC C1422 is not output

DTC C1422 is output

4.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

5.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (STP) - A5-1 Always Below 1 Ω
A64-2 (STP) or A5-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR