Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  New Key cannot be Registered  


DESCRIPTION

If an electrical key transmitter could not be newly registered, wave interference or a malfunction of the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly, steering lock ECU (steering lock actuator assembly) or door control receiver is suspected.

The registration to add another electrical key transmitter sub-assembly (without replacing any parts) is called "additional key ID registration"

If additional registration is not possible, refer to "Additional Key cannot be Registered".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>Additional Key cannot be Registered

HINT:
If any of the following have been performed, new registration of the electrical key transmitter sub-assembly is necessary:
·

The certification ECU (smart key ECU assembly) has been replaced.

·

The certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) have been replaced.



WIRING DIAGRAM

B274830
2.031,0.677 2.99,0.833 0.958,0.156 10 false IGN 3.188,0.563 3.531,0.792 0.344,0.229 10 false IG 2.823,0.552 3.229,0.896 0.406,0.344 10 false G84 2.927,0.375 3.146,0.615 0.219,0.24 10 false 5 3.188,1.073 3.854,1.396 0.667,0.323 10 false CUTB 2.823,1.063 3.323,1.375 0.5,0.313 10 false G82 2.885,0.885 3.177,1.104 0.292,0.219 10 false 10 5.469,0.396 5.729,0.625 0.26,0.229 10 false 5 5.688,0.563 5.969,0.719 0.281,0.156 10 false LIN 3.833,0.563 4.24,0.865 0.406,0.302 10 false LIN 5.49,0.854 5.802,1.01 0.313,0.156 10 false G5 4.146,0.375 4.417,0.573 0.271,0.198 10 false 17 3.188,1.583 3.542,1.906 0.354,0.323 10 false +B 2.823,1.583 3.302,1.917 0.479,0.333 10 false G82 2.917,1.406 3.073,1.563 0.156,0.156 10 false 2 3.188,3.24 3.583,3.396 0.396,0.156 10 false TXCT 2.927,3.063 3.229,3.354 0.302,0.292 10 false 9 3.188,3.677 3.667,3.833 0.479,0.156 10 false CODE 2.927,3.5 3.156,3.719 0.229,0.219 10 false 7 3.188,2.365 3.885,2.792 0.698,0.427 10 false SWIL 2.885,2.188 3.177,2.406 0.292,0.219 10 false 16 3.188,4.115 3.813,4.427 0.625,0.313 10 false AGND 2.885,3.938 3.281,4.219 0.396,0.281 10 false 24 1.656,2.229 1.865,2.438 0.208,0.208 10 false 9 1.656,3.104 1.906,3.323 0.25,0.219 10 false 7 1.656,3.542 1.948,3.906 0.292,0.365 10 false 8 1.656,3.979 2.031,4.396 0.375,0.417 10 false 6 1.646,2.667 1.865,2.823 0.219,0.156 10 false 10 0.479,4.427 0.885,4.646 0.406,0.219 10 false G24 3.188,2.802 3.719,3.104 0.531,0.302 10 false VC5 1.167,3.198 1.635,3.354 0.469,0.156 10 false TXCT 1.125,3.635 1.594,3.792 0.469,0.156 10 false CODE 1.188,2.323 1.552,2.479 0.365,0.156 10 false SWIL 1.125,4.073 1.594,4.229 0.469,0.156 10 false AGND 1.24,2.76 1.542,2.917 0.302,0.156 10 false VC5 2.938,2.573 3.115,2.729 0.177,0.156 10 false 1 1.76,1.219 2.615,1.375 0.854,0.156 10 false ECU-B NO.1 2.01,1.708 2.615,2.198 0.604,0.49 10 false AM2 0.354,0.531 1.542,0.833 1.188,0.302 10 false from IG2 Relay 0.49,1.052 1.646,1.396 1.156,0.344 10 false from Battery 0.5,1.573 1.458,1.802 0.958,0.229 10 false from Battery 0.469,4.573 1.698,4.729 1.229,0.156 10 false Engine Switch 2.698,4.927 4.51,5.302 1.813,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.469,5.25 7.094,5.448 1.625,0.198 10 false : LIN Communication Line 5.49,1.021 6.99,1.896 1.5,0.875 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 2.823,2.365 3.292,2.656 0.469,0.292 10 false G84 4.094,0.552 4.458,0.833 0.365,0.281 10 false G84 2.823,2.802 3.26,3.104 0.438,0.302 10 false G84 2.823,3.24 3.229,3.5 0.406,0.26 10 false G84 2.823,3.677 3.177,3.927 0.354,0.25 10 false G84 2.823,4.104 3.281,4.458 0.458,0.354 10 false G84

CAUTION / NOTICE / HINT

NOTICE:
·

If registration of an electrical key transmitter sub-assembly is not possible, first confirm the procedure by immobiliser system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

A new registration mode can be entered only when no electrical key transmitter sub-assemblies are stored in the certification ECU (smart key ECU assembly).

·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

·

Before replacing the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), refer to the smart key system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Smart Key > Trouble Codes
50001 125
NOTICE:

If a malfunction occurs, do not remove/install the vehicle battery before checking for DTCs.



Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.READ VALUE USING TECHSTREAM (OPERATION HISTORY LIST)

DTC is output

2.READ VALUE USING TECHSTREAM (OPERATION HISTORY LIST)
a.

Connect the Techstream to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Smart Key / Utility / Operation History.


e.

Check the freeze frame data and follow the instructions in the step column of the table below.


Certification ECU Log of ID code registration
Parameter Name Detection Condition Trouble Area Step
Failed Registration Mode
·

A registration request was sent while in another mode.

·

During registration a different registration request was sent.


- Go to step *1
Vehicle ID not set A vehicle ID has not been registered in the certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) Replace certification ECU (smart key ECU assembly)
(Click here)
Key Registration Max A registration request is sent when the maximum number of electrical key transmitter sub-assemblies has already been registered. Certification ECU (smart key ECU assembly) Go to step *4
ID-BOX Error A registration request is sent even though whether or not the vehicle is provided with an ID code box is unknown. Certification ECU (smart key ECU assembly) Check for DTC B2789
Vehicle Speed Too High A registration request is sent with a vehicle speed of 5 km/h (3 mph) or more. - Check if the vehicle is stationary. If a code cannot be registered even though the vehicle is stationary, then go to step *2
No ECU Response The steering lock ECU (steering lock actuator assembly) was not connected. Certification ECU (smart key ECU assembly)
Steering lock ECU (steering lock actuator assembly)
Check for DTC B2785 or B2786
L Code Verification Error The L codes registered in the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) did not match. Certification ECU (smart key ECU assembly)
Steering lock ECU (steering lock actuator assembly)
Go to step *3
Key Verification: Max Number The number of electrical key transmitter sub-assemblies registered in the steering lock ECU (steering lock actuator assembly) was more than 7. Steering lock ECU (steering lock actuator assembly) Replace steering lock ECU (steering lock actuator assembly)
(Click here)
Key Verification: Amp Abnormal Malfunction of the immobiliser amplifier, such as a short to ground. Certification ECU (smart key ECU assembly)Engine switch Check for DTC B278A or B2784
Key Verification: Read Error Although a registered electrical key transmitter sub-assembly was held near the engine switch, immobiliser system certification did not succeed. Certification ECU (smart key ECU assembly)
Electrical key transmitter sub-assembly
Go to step *5
Unverified Key Although all of the registered electrical key transmitter sub-assemblies had been held near the engine switch, electrical key transmitter sub-assembly registration was not possible due to immobiliser system certification not being able to succeed. Certification ECU (smart key ECU assembly)
Electrical key transmitter sub-assembly
Go to step *6
Transponder Key Amp Error Malfunction of the immobiliser amplifier, such as a short to ground. Certification ECU (smart key ECU assembly)
Engine switch
Check for DTC B278A or B2784
New Key Registration Error Although an unregistered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration is not possible due to immobiliser system certification not being able to succeed. Certification ECU (smart key ECU assembly)
Electrical key transmitter sub-assembly
Engine switch
Go to step *7
New Key Vehicle ID Error Although an unregistered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration is not possible due to the vehicle ID not being stored successfully. Certification ECU (smart key ECU assembly)
Electrical key transmitter sub-assembly
Go to step *7
New Key Registration Failed After successful immobiliser system certification, time expired before smart recognition completion confirmation or a registration cancellation request was sent. Certification ECU (smart key ECU assembly)
Electrical key transmitter sub-assembly
Go to step *7
New Key Already Registered Although a registered electrical key transmitter sub-assembly was held near the engine switch, time expired or a registration cancellation request was sent. - Check if a registered electrical key transmitter sub-assembly was held near the engine switch instead of an unregistered electrical key transmitter sub-assembly by mistake. Perform registration again using an unregistered electrical key transmitter sub-assembly. If the same problem occurs again, replace the certification ECU (smart key ECU assembly).
(Click here)
New Key ID Code Error Electrical key transmitter sub-assembly registration was not possible due to the certification ECU (smart key ECU assembly) not being able to store the information of the electrical key transmitter sub-assembly to EEPROM correctly. Certification ECU (smart key ECU assembly) Replace certification ECU (smart key ECU assembly)
(Click here)
No Response Registering L/S Code The certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) was not connected. Certification ECU (smart key ECU assembly)
Steering lock ECU (steering lock actuator assembly)
Check for DTC B2785
L Code Verification NG The L code could not be stored by the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly). Certification ECU (smart key ECU assembly)
Steering lock ECU (steering lock actuator assembly)
Go to step *3
Key Number Write Error The certification ECU (smart key ECU assembly) could not store the number of electrical key transmitter sub-assemblies to EEPROM. Certification ECU (smart key ECU assembly) Replace certification ECU (smart key ECU assembly)
(Click here)
ID Code BOX Write Error The certification ECU (smart key ECU assembly) could not store the information of whether or not the ID code box was provided in the vehicle to EEPROM. Certification ECU (smart key ECU assembly) Replace certification ECU (smart key ECU assembly)
(Click here)

Result:
Proceed to
*1
*2
*3
*4
*5
*6
*7



*1

3.CHECK REGISTRATION MODE

*2

4.READ VALUE USING TECHSTREAM (VEHICLE SPEED)

*3

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*4

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*5

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

*6

11.CHECK FOR ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

*7

13.REREGISTRATION
3.CHECK REGISTRATION MODE
a.

Make sure that another mode or different registration mode is not selected.

OK:

Another mode or a different registration mode is not selected.


HINT:

If any mode has been selected, it is necessary to cancel the mode.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
OK:

"0 km/h (0 mph)" is displayed when the vehicle is stationary.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies to the new ECU.

HINT:


OK:

Registration to the new certification ECU (smart key ECU assembly) has completed successfully.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

6.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies to the new ECU.

HINT:



Result:
Proceed to
NEXT



NEXT

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Make sure that a registered electrical key transmitter sub-assembly is used.

OK:

A registered electrical key transmitter sub-assembly is used.



Result:
Proceed to
OK
NG



OK

8.CHECK NUMBER OF REGISTERED ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLIES

NG

USE A REGISTERED ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY AND REREGISTRATION

8.CHECK NUMBER OF REGISTERED ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLIES
a.

Check the number of registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
When only one electrical key transmitter sub-assembly is registered A
When 2 or more electrical key transmitter sub-assemblies are registered B



A

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

10.REREGISTRATION
9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies to the new ECU.

HINT:


OK:

Registration to the new certification ECU (smart key ECU assembly) has completed successfully.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

10.REREGISTRATION
a.

Reregister the electrical key transmitter sub-assemblies using different order combinations.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

OK:

"Key Verification Error" is not displayed.


HINT:

If there are 2 or more electrical key transmitter sub-assemblies, make sure that the number of order combinations is the same as the number of electrical key transmitter sub-assemblies so that each transmitter can be checked first.


Example: When there are 3 registered electrical key transmitter sub-assemblies (A, B and C).
Combination Order*
1 A → B → C
2 B → C→ A
3 C → A → B

*: Except the first electrical key transmitter sub-assembly, the remaining electrical key transmitter sub-assemblies can be checked in any order.



HINT:

The electrical key transmitter sub-assembly held near the engine switch when the malfunction was detected is defective. The defective electrical key transmitter sub-assembly is the one that should be replaced.


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

11.CHECK FOR ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check that all registered electrical key transmitter sub-assemblies are available.

OK:

No registered electrical key transmitter sub-assemblies are missing.



Result:
Proceed to
OK
NG



OK

12.REREGISTRATION

NG

ERASE ALL REGISTERED ELECTRICAL KEY TRANSMITTERS EXCEPT ONE, THEN REGISTER THE REMAINING ELECTRICAL KEY TRANSMITTERS

12.REREGISTRATION
a.

Reregister the electrical key transmitter sub-assemblies using different order combinations.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

OK:

"Key Verification Error" is not displayed.


HINT:

If there are 2 or more electrical key transmitters, make sure that the number of order combinations is the same as the number of electrical key transmitters so that each transmitter can be checked first.


Example: When there are 3 registered electrical key transmitter sub-assemblies (A, B and C).
Combination Order*
1 A → B → C
2 B → C→ A
3 C → A → B

*: Except the first electrical key transmitter sub-assembly, the remaining electrical key transmitter sub-assemblies can be checked in any order.



HINT:

The electrical key transmitter sub-assembly held near the engine switch when the malfunction was detected is defective. The defective electrical key transmitter sub-assembly is the one that should be replaced.


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

13.REREGISTRATION
a.

Using an unregistered electrical key transmitter sub-assembly, register the ID.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

OK:

The key ID can be registered.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)