Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  Additional Key cannot be Registered  


DESCRIPTION

If additional registration is not possible, a malfunction in the certification ECU (smart key ECU assembly), engine switch, electrical key transmitter sub-assembly or steering lock ECU (steering lock actuator assembly) is suspected.

CAUTION / NOTICE / HINT

NOTICE:
·

If registration of an electrical key transmitter sub-assembly is not possible, first confirm the procedure by engine immobiliser system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly) and electrical key transmitter sub-assembly, refer to the smart key system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION



HINT:

When additional registration is not possible, some freeze frame data may be stored in the certification ECU (smart key ECU assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION HISTORY LIST

If freeze frame data is available, it can be helpful in determining whether any parts were malfunctioning or not or narrowing down the suspected areas based on the table below.


Certification ECU Log of ID Code Registration
Parameter Name Cause of Problem and Countermeasure
Failed Registration Mode Make sure that another mode or a different registration mode is not selected, and then restart registration.
Key Registration Max The registration was not possible because the maximum number of the electrical key transmitter sub-assemblies has already been registered to the certification ECU (smart key ECU assembly).
If a new electrical key transmitter sub-assembly needs to be registered, such as when one of the registered electrical key transmitter sub-assemblies has been lost, erase an unnecessary ID code first. (Click here(Click here))
Key Verification: Amp Abnormal Although a registered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration could not be confirmed due to a malfunction of the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 was stored.
Key Verification: Read Error A registered electrical key transmitter sub-assembly was not held near the engine switch properly or electrical key transmitter sub-assembly registration cannot be confirmed due to wave interference, etc.
Reregister the electrical key transmitter sub-assembly using the correct procedure or use another registered electrical key transmitter sub-assembly.
Transponder Key Amp Abnormal Although an unregistered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration cannot be completed due to a malfunction of the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 was stored.
New Key Registration Error An unregistered electrical key transmitter sub-assembly was not held near the engine switch properly or electrical key transmitter sub-assembly registration cannot be confirmed due to a malfunction, such as wave interference.
Reregister the electrical key transmitter sub-assembly using the correct procedure or use another registered electrical key transmitter sub-assembly.
New Key Vehicle ID Error Although the vehicle ID stored in the certification ECU (smart key ECU assembly) should be registered to the electrical key transmitter sub-assembly during electrical key transmitter sub-assembly registration, it was not successful.
Use another unregistered electrical key transmitter sub-assembly for registration.
New Key Registration Failed Although an unregistered electrical key transmitter sub-assembly was held near the engine switch for registration, electrical key transmitter sub-assembly registration was not successful due to wave interference (such as radio waves emitted from a device in the cabin) or a low transmitter battery.
New Key Already Registered As a registered electrical key transmitter sub-assembly was held near the engine switch by mistake, electrical key transmitter sub-assembly registration was not successful.
Using an unregistered electrical key transmitter sub-assembly, perform the registration procedure again.
New Key ID Code Error Replace the certification ECU (smart key ECU assembly)
New Key Information Abnormal The ID code of an electrical key transmitter sub-assembly could not be registered to the certification ECU (smart key ECU assembly). If 2 electrical key transmitter sub-assemblies are held near the engine switch at the same time, incorrect registration information will be stored in the certification ECU (smart key ECU assembly), suspending registration.
Reregister the electrical key transmitter sub-assembly using the correct registration procedure.

PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125
NOTICE:

If a malfunction occurs, do not remove/install the vehicle battery before checking for DTCs.



Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK STEERING LOCK SYSTEM

DTC is output

2.CHECK STEERING LOCK SYSTEM
a.

Check that the steering wheel unlocks.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

OK:

The steering wheel unlocks.


HINT:

Check that the communication between the steering lock ECU (steering lock actuator assembly) and certification ECU (smart key ECU assembly) is normal.



Result:
Proceed to
OK
NG



OK

3.REGISTRATION

NG

3.REGISTRATION
a.

Using other unregistered electrical key transmitter sub-assemblies, perform the additional registration procedure.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

OK:

Additional registration can be completed.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies to the new ECU.

HINT:


OK:

The key ID can be registered.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG