Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and front door outside handle assembly [for front passenger door] [front passenger door electrical key antenna]), or there may be wave interference.

HINT:

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


Radio Wave Interference
Parameter Name Cause of Problem and Countermeasure
Lock / Key RF Signal Interference When entry lock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. If the cause of the malfunction has not been stored but the car has been moved and an entry lock operation has been successfully performed, the possibility of wave interference is high.
Unlock / Key RF Signal Interference When entry unlock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. If the cause of the malfunction has not been stored but the car has been moved and an entry unlock operation has been successfully performed, the possibility of wave interference is high.

WIRING DIAGRAM

B341225
0.323,3.479 1.365,3.677 1.042,0.198 10 false I7 1.271,0.719 1.969,0.896 0.698,0.177 10 false ANT1 1.26,1.188 1.958,1.365 0.698,0.177 10 false ANT2 1.542,1.635 2.24,1.813 0.698,0.177 10 false B 1.24,2.094 1.938,2.271 0.698,0.177 10 false SENS 1.24,2.563 1.938,2.74 0.698,0.177 10 false TRG+ 1.323,3.031 2.021,3.208 0.698,0.177 10 false GND 5.75,0.708 6.448,0.885 0.698,0.177 10 false CLG2 5.729,1.156 6.427,1.333 0.698,0.177 10 false CG2B 5.74,1.646 6.438,1.823 0.698,0.177 10 false POS2 5.75,2.083 6.448,2.26 0.698,0.177 10 false SEN2 5.75,2.563 6.448,2.74 0.698,0.177 10 false TSW2 5.729,3.021 6.427,3.198 0.698,0.177 10 false E 5.438,0.552 6.135,0.729 0.698,0.177 10 false 11 5.438,1.021 6.135,1.198 0.698,0.177 10 false 10 5.448,1.469 6.146,1.646 0.698,0.177 10 false 21 5.438,1.938 6.135,2.115 0.698,0.177 10 false 23 5.448,2.396 6.146,2.573 0.698,0.177 10 false 8 5.438,2.854 6.135,3.031 0.698,0.177 10 false 11 5.375,0.729 6.073,0.906 0.698,0.177 10 false G84 5.365,1.188 6.063,1.365 0.698,0.177 10 false G84 5.365,1.646 6.063,1.823 0.698,0.177 10 false G84 5.365,2.115 6.063,2.292 0.698,0.177 10 false G84 5.375,2.573 6.073,2.75 0.698,0.177 10 false G84 5.375,3.031 6.073,3.208 0.698,0.177 10 false G82 1.76,0.604 2.458,0.781 0.698,0.177 10 false 6 1.771,1.073 2.469,1.25 0.698,0.177 10 false 3 1.76,1.542 2.458,1.719 0.698,0.177 10 false 5 1.771,2.01 2.469,2.188 0.698,0.177 10 false 4 1.76,2.458 2.458,2.635 0.698,0.177 10 false 1 1.76,2.927 2.458,3.104 0.698,0.177 10 false 2 0.323,3.635 2.646,4.208 2.323,0.573 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.208,3.542 7.104,4.094 1.896,0.552 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Door locks operate normally
Door locks do not operate



Door locks operate normally

2.CHECK WAVE ENVIRONMENT

Door locks do not operate

2.CHECK WAVE ENVIRONMENT
a.
B340882
1.406,1.135 1.719,1.333 0.313,0.198 10 *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Proceed to
Entry function does not operate normally
Entry function operates normally



Entry function does not operate normally

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU AND BODY GROUND)

Entry function operates normally

AFFECTED BY WAVE INTERFERENCE

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the I7 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-3 (ANT2) - G84 -10 (CG2B) Always Below 1 Ω
I7-6 (ANT1) - G84-11 (CLG2) Always Below 1 Ω
I7-5 (B) - G84-21 (POS2) Always Below 1 Ω
I7-2 (GND) - Body ground Always Below 1 Ω
I7-3 (ANT2) or G84-10 (CG2B) - Body ground Always 10 kΩ or higher
I7-6 (ANT1) or G84-11 (CLG2) - Body ground Always 10 kΩ or higher
I7-5 (B) or G84-21 (POS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)
a.
B250975
0.26,0.573 0.542,0.771 0.281,0.198 0.823,0.344 1.083,0.354 1.083,0.354 1.688,0.802 false 0.865,1.302 1.146,1.292 1.146,1.292 1.698,0.938 false 2.531,1.292 2.26,1.302 2.26,1.302 1.844,0.948 false 2.552,0.385 2.323,0.385 2.323,0.385 1.813,0.792 false 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.094,1.594 0.406,1.792 0.313,0.198 10 false *b 0.063,2.458 0.552,2.667 0.49,0.208 10 false GND 0.427,0.25 0.917,0.458 0.49,0.208 10 false GND 0.688,1.208 1.177,1.417 0.49,0.208 10 false B 2.615,0.302 3.104,0.51 0.49,0.208 10 false ANT2 2.583,1.219 3.073,1.427 0.49,0.208 10 false ANT1 0.323,0.583 0.813,0.792 0.49,0.208 10 false I7
*a Front view of wire harness connector
(to Front Door Outside Handle Assembly [for Driver Door])
*b Waveform


Connect the G84 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I7-5 (B) - I7-2 (GND) Engine switch off → on (IG) 9 to 14 V → Below 2 V



c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
I7-3 (ANT2) - I7-6 (ANT1)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)


*: For details about the areas that are inside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FRONT PASSENGER DOOR) (OPERATION)
6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FRONT PASSENGER DOOR) (OPERATION)
a.

Check that the entry functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry functions operate normally.



Result:
Proceed to
OK
NG



OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR FRONT PASSENGER DOOR] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)