Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15FE  XM Tuner Antenna Disconnected  B15FF  XM Tuner Antenna Short  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the satellite radio antenna which is connected to the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15FE XM Tuner Antenna Disconnected Satellite radio antenna is not connected.
·

Satellite radio antenna cable

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna with holder assembly

·

Radio and display receiver assembly


B15FF XM Tuner Antenna Short A short occurs in satellite radio antenna.
·

Satellite radio antenna cable

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Antenna with holder assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E288613
5.854,2.25 6.167,2.448 0.313,0.198 10 false SD 5.854,2.427 7.083,2.833 1.229,0.406 10 false Stereo Component Tuner Assembly 3.24,2.177 4.49,2.583 1.25,0.406 10 false No. 2 Antenna Cord Sub-assembly 4.75,2.177 5.646,2.583 0.896,0.406 10 false Antenna Cord Sub-assembly 1.781,2.167 3.031,2.573 1.25,0.406 10 false No. 3 Antenna Cord Sub-assembly 0.167,1.677 1.417,2.083 1.25,0.406 10 false Antenna with Holder Assembly 1.083,0.094 2.25,0.5 1.167,0.406 10 false Roof Antenna Pole Sub-assembly 5.458,1.083 5.625,1.25 0.167,0.167 10 false 1 5.396,1.375 5.708,1.542 0.313,0.167 10 false 1a 4.75,1.083 4.917,1.25 0.167,0.167 10 false 1 4.76,1.375 5.052,1.552 0.292,0.177 10 false 1a 4.083,1.083 4.25,1.25 0.167,0.167 10 false 2 3.99,1.365 4.302,1.531 0.313,0.167 11 false 2a 3.354,1.094 3.521,1.26 0.167,0.167 10 false 2 3.354,1.385 3.74,1.573 0.385,0.188 10 false 2a 2.073,1.104 2.24,1.271 0.167,0.167 10 false 1 2.073,1.385 2.354,1.552 0.281,0.167 10 false 1a 2.646,1.083 2.813,1.25 0.167,0.167 10 false 2 2.573,1.385 2.854,1.583 0.281,0.198 10 false 2a

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTION OF SATELLITE RADIO ANTENNA CABLE
a.

Check if the satellite radio antenna cable is securely connected to the radio and display receiver assembly.

OK:

Satellite radio antenna cable is securely connected



Result:
Proceed to
OK
NG



OK

2.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

SECURELY CONNECT SATELLITE RADIO ANTENNA CABLE

2.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288617
0.594,0.729 1.104,1.021 0.51,0.292 1.875,1.115 2.208,1.417 2.208,1.417 2.458,1.417 true 1.948,2.542 2.281,2.125 2.281,2.125 2.531,2.125 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.104,1.75 0.417,1.948 0.313,0.198 10 false *b 2.51,1.333 2.823,1.531 0.313,0.198 10 false 1a 2.583,2.042 2.896,2.24 0.313,0.198 10 false 1a 0.75,0.792 1.063,0.99 0.313,0.198 10 false SD
*a Front view of wire harness connector
(to Stereo Component Tuner Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Remove the antenna connector from the stereo component tuner assembly.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SD-1 - 1 Always Below 1 Ω
SD-1a - 1a Always Below 1 Ω
SD-1 - Body ground Always 10 kΩ or higher
SD-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288615
1.323,0.583 1.156,0.25 1.156,0.25 0.906,0.25 true 2.167,2.333 2.333,2 2.333,2 2.583,2 true 0.698,0.156 1.01,0.354 0.313,0.198 10 false 1a 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.104,1.885 0.417,2.083 0.313,0.198 10 false *b 2.625,1.917 2.938,2.115 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1a - 2a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E288616
1.938,2.542 2.271,2.208 2.271,2.208 2.521,2.208 true 1.385,0.844 1.052,0.51 1.052,0.51 0.802,0.51 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.104,1.719 0.417,1.917 0.313,0.198 10 false *b 2.552,2.125 2.865,2.323 0.313,0.198 10 false 1a 0.604,0.417 0.917,0.615 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna with Holder Assembly)


Remove the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Remove the antenna connector from the antenna with holder assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
2a - 1a Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly



Result:
Proceed to
OK
NG



OK

6.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

6.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)

NG

7.CHECK ANTENNA WITH AMPLIFIER ASSEMBLY
7.CHECK ANTENNA WITH AMPLIFIER ASSEMBLY
a.

Replace the antenna with holder assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG

8.CHECK STEREO COMPONENT TUNER ASSEMBLY
8.CHECK STEREO COMPONENT TUNER ASSEMBLY
a.

Replace the stereo component tuner assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (STEREO COMPONENT TUNER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY