Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15FE  XM Tuner Antenna Disconnected  B15FF  XM Tuner Antenna Short  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the satellite radio antenna which is connected to the navigation receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15FE XM Tuner Antenna Disconnected Satellite radio antenna is not connected.
·

Roof antenna pole sub-assembly

·

Antenna with holder assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Stereo component tuner assembly

·

Navigation receiver assembly


B15FF XM Tuner Antenna Short A short occurs in satellite radio antenna.
·

Roof antenna pole sub-assembly

·

Antenna with holder assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Stereo component tuner assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E288793
0.063,0.25 1.323,0.615 1.26,0.365 10 false Roof Antenna Pole Sub-assembly 0.385,1.854 1.646,2.219 1.26,0.365 10 false Antenna with Holder Assembly 2.104,2.156 3.365,2.521 1.26,0.365 10 false No. 3 Antenna Cord Sub-assembly 3.552,2.135 4.813,2.5 1.26,0.365 10 false No. 2 Antenna Cord Sub-assembly 4.979,2.135 5.906,2.5 0.927,0.365 10 false Antenna Cord Sub-assembly 5.844,2.906 7.073,3.281 1.229,0.375 10 false Stereo Component Tuner Assembly 2.698,0.979 2.917,1.188 0.219,0.208 10 false 1 2.688,1.292 2.906,1.5 0.219,0.208 10 false 1-a 3.083,0.99 3.302,1.198 0.219,0.208 10 false 2 3.042,1.281 3.333,1.479 0.292,0.198 10 false 2-a 3.792,0.99 4.01,1.198 0.219,0.208 10 false 2 3.792,1.292 4.01,1.5 0.219,0.208 10 false 2-a 4.26,0.99 4.479,1.198 0.219,0.208 10 false 1 4.167,1.292 4.385,1.5 0.219,0.208 10 false 1-a 4.927,1 5.146,1.208 0.219,0.208 10 false 1 4.938,1.271 5.156,1.479 0.219,0.208 10 false 1-a 5.469,0.99 5.688,1.198 0.219,0.208 10 false 1 5.375,1.281 5.594,1.49 0.219,0.208 10 false 1-a

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTION OF ANTENNA CORD SUB-ASSEMBLY
a.

Check if the antenna cord sub-assembly is securely connected to the stereo component tuner assembly.

OK:

Antenna cord sub-assembly is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

SECURELY CONNECT ANTENNA CORD SUB-ASSEMBLY

2.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E288794
1.948,0.885 2.24,0.615 2.24,0.615 2.438,0.615 true 1.427,2.51 0.948,2.781 0.948,2.781 0.792,2.781 true 0.385,0.156 0.698,0.313 0.313,0.156 10 false *a 0.448,1.708 0.76,1.865 0.313,0.156 10 false *b 2.479,0.531 2.875,0.698 0.396,0.167 10 false 1-a 0.552,2.677 0.948,2.844 0.396,0.167 10 false 2-a
*a Front view of wire harness connector
(to Antenna with Holder Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna with holder assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1-a - 2-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795
0.74,2.573 0.927,2.573 0.927,2.573 1.208,2.417 true 2.135,0.781 2.385,0.646 2.385,0.646 2.583,0.646 true 0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b 2.646,0.563 3.031,0.771 0.385,0.208 10 false 2-a 0.51,2.448 0.896,2.656 0.385,0.208 10 false 1-a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
2-a - 1-a Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
2-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E291139
2.083,0.833 2.5,0.417 2.5,0.417 2.667,0.417 true 1.938,2.583 2.354,2.167 2.354,2.167 2.521,2.167 true 0.188,0.219 0.5,0.417 0.313,0.198 10 false *a 0.219,2 0.531,2.198 0.313,0.198 10 false *b 2.719,0.333 2.99,0.51 0.271,0.177 10 false 1-a 2.573,2.083 2.844,2.26 0.271,0.177 10 false 1-a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Stereo Component Tuner Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the stereo component tuner assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 1 Always Below 1 Ω
1-a - 1-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly.



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA WITH HOLDER ASSEMBLY

NG

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

6.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG

7.CHECK STEREO COMPONENT TUNER ASSEMBLY
7.CHECK STEREO COMPONENT TUNER ASSEMBLY
a.

Replace the stereo component tuner assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>SATELLITE RADIO TUNER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (STEREO COMPONENT TUNER ASSEMBLY IS DEFECTIVE)

NG