Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2013.11
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050872 CYLINDER HEAD GASKET A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL CYLINDER HEAD GASKET

a.

Clean the cylinder block and cylinder head with solvent.


b.
A264847
2.406,0.156 2.26,0.156 2.26,0.156 2.177,0.448 false 0.781,3.229 0.469,3.646 0.469,3.646 0.469,3.802 false 1.063,2.698 1.125,2.354 1.125,2.354 1.24,2.354 false 2.427,0.052 2.615,0.229 0.188,0.177 10 *1 1.844,3.042 2,3.25 0.156,0.208 10 *b 2.396,3.948 2.594,4.115 0.198,0.167 10 *c 1.281,2.25 1.49,2.427 0.208,0.177 10 *a 0.802,3.531 0.979,3.719 0.177,0.188 10 *2 0.385,3.823 0.542,3.99 0.156,0.167 10 *3 0.271,2.958 0.448,3.146 0.177,0.188 10 *d
*1 Lot No.
*2 Cylinder Block
*3 Cylinder Head Gasket
*a 3.0 to 7.0 mm (0.118 to 0.276 in.)
*b 20 mm (0.787 in.) or more
*c 7.0 mm (0.276 in.)
*d 3.0 mm (0.118 in.) or more
V100135

Seal Packing
V100136

Front


Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal dimension:

3.0 to 7.0 mm (0.118 to 0.276 in.) wide and 3.0 mm (0.118 in.) thick


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



HINT:

Apply at least 20 mm (0.787 in.) of seal packing from the inside edge of the protrusion of the cylinder block.



c.

Place a new cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

NOTICE:

Pay attention to the installation direction.



Hide 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head.

·

Place the cylinder head on the cylinder block gently in order not to damage the gasket with the bottom part of the head.



HINT:

The cylinder head bolts are tightened in 4 progressive steps.



b.

Install the plate washers to the cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
A284098
1.5,1.677 1.656,1.875 0.156,0.198 10 1 1.49,0.292 1.646,0.49 0.156,0.198 10 2 1.958,1.677 2.115,1.875 0.156,0.198 10 3 1.948,0.292 2.104,0.49 0.156,0.198 10 5 2.427,1.677 2.583,1.875 0.156,0.198 10 7 2.406,0.292 2.563,0.49 0.156,0.198 10 9 1.021,1.667 1.177,1.865 0.156,0.198 10 6 1.042,0.292 1.198,0.49 0.156,0.198 10 4 0.51,1.656 0.771,1.854 0.26,0.198 10 10 0.583,0.292 0.74,0.49 0.156,0.198 10 8

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the plate washer for the cylinder head bolt into the cylinder head.




e.

Step 2:

i.

Tighten the cylinder head bolts again in the sequence shown in the illustration to make sure that they are tightened to the specified torque.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



f.

Step 3:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



g.

Step 4:

i.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.


ii.

Check that the paint marks are now at a 180° angle to the front.

NOTICE:
·

Do not apply oil for at least 4 hours after the installation.

·

Do not start the engine for at least 4 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.





Hide 3.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.

Install the 16 valve stem caps to the cylinder head.

NOTICE:

Do not drop the valve stem caps into the cylinder head.



Hide 4.SET CAMSHAFT TIMING GEAR ASSEMBLY

HINT:
·

When reusing the camshaft timing gear, release the lock pin and set the camshaft timing gear to the advanced position before installation.

·

If the camshaft timing gear is new or has already been set to the advanced position, install the camshaft timing gear after the camshafts have been installed to the engine.



a.
A284096
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 false 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 false 2.031,1.594 2.448,1.938 2.448,1.938 2.604,1.938 false 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 false 0.083,0.25 0.396,0.406 0.313,0.156 10 *a 0.083,2.583 0.396,2.74 0.313,0.156 10 *b 0.708,1.625 1.021,1.781 0.313,0.156 10 *1 2.667,1.844 2.979,2 0.313,0.156 10 *2 2.635,3.323 2.948,3.479 0.313,0.156 10 *2 0.604,3.854 0.917,4.01 0.313,0.156 10 *1
*1 Knock Pin Hole
*2 Alignment Mark
*a Advanced Position
*b Retarded Position


Check the camshaft timing gear position.

NOTICE:

If the camshaft timing gear is set to the advanced position, do not let the camshaft timing gear rotate clockwise during installation.

If the camshaft timing gear rotates to the retarded position, release the lock pin and set the camshaft timing gear to the advanced position.



b.
A196901
1.284,0.128 1.464,0.305 0.181,0.177 10 *1 2.017,0.54 2.185,0.717 0.168,0.177 10 *2 1.983,0.626 1.854,0.626 1.854,0.626 1.639,0.907 false 1.252,0.213 1.123,0.213 1.123,0.213 0.693,0.772 false
*1 Pin Hole
*2 Knock Pin


Align the knock pin of the camshaft with the pin hole of the camshaft timing gear and attach the gear to the camshaft.


c.
A196904
2.167,0.844 1.917,0.844 1.917,0.844 1.521,1.063 false 0.823,0.75 0.917,0.75 0.917,0.75 1.125,0.969 false 0.604,0.635 0.823,0.792 0.219,0.156 10 *1 1.802,0.531 2.021,0.698 0.219,0.167 10 *2 2.208,0.729 2.438,0.906 0.229,0.177 10 *3 1.74,2.021 1.969,2.177 0.229,0.156 10 *c 0.063,0.042 0.281,0.24 0.219,0.198 10 *a 0.063,1.833 0.281,2.031 0.219,0.198 10 *b
*1 Camshaft Timing Gear
*2 Clearance
*3 Camshaft Flange
*a INCORRECT
*b CORRECT
*c No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


d.

Fix the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



e.

Release the lock pin.

i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

A284097
1.417,1.052 1.771,1.052 1.771,1.052 1.917,1.104 false 2.344,1.229 2.479,1.125 2.479,1.125 2.781,1.125 false 1.344,2.552 1.635,2.552 1.635,2.552 1.771,2.427 false 4.813,1.156 5.073,1.156 5.073,1.156 5.323,1.604 false 4.615,1.51 4.76,1.51 4.76,1.51 5.094,1.76 false 4.615,2.521 4.813,2.521 4.813,2.521 5.125,2.135 false 5.604,1.771 5.948,1.448 5.948,1.448 6.146,1.448 false 5.552,2.167 5.885,2.469 5.885,2.469 6.094,2.469 false 4.615,1.073 4.927,1.229 0.313,0.156 10 *4 1.229,0.948 1.542,1.104 0.313,0.156 10 *1 2.844,1.031 3.156,1.188 0.313,0.156 10 *2 4.438,1.406 4.75,1.563 0.313,0.156 10 *a 4.448,2.417 4.76,2.573 0.313,0.156 10 *b 6.135,2.365 6.448,2.521 0.313,0.156 10 *b 6.188,1.344 6.5,1.5 0.313,0.156 10 *b 1.156,2.469 1.333,2.635 0.177,0.167 10 *3
*1 Retard Side Path *2 Advance Side Path
*3 Port A *4 Knock Pin
*a Open *b Closed
V100144

Rubber
V100145

Vinyl Tape


HINT:

There are 4 oil paths in the grooves of the camshaft. Plug three of the paths with pieces of rubber.



iii.

Open a hole at port A shown in the illustration.


iv.
A196906

While applying compressed air at approximately 200 kPa (2.0 kgf/ cm2, 29 psi) to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.


NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.


HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




v.

Remove the vinyl tape and pieces of rubber from the camshaft.



f.

Remove the bolt and camshaft timing gear.

NOTICE:

Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.



Hide 5.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the valve lash adjuster before installing it.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


b.

Install the 16 lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster to the same place it was removed from.



Hide 6.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A196911
1.208,0.323 1.427,0.323 1.427,0.323 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.698,0.958 0.875,0.958 0.875,0.958 1.073,1.083 false 2.896,0.938 3.094,1.26 0.198,0.323 10 *2 1,0.208 1.177,0.385 0.177,0.177 10 *1 0.479,0.844 0.677,1.177 0.198,0.333 10 *3
*1 Valve Rocker Arm
*2 Valve Lash Adjuster
*3 Valve Stem Cap


Apply engine oil to the lash adjuster tips and valve stem caps.


b.

Install the 16 valve rocker arms as shown in the illustration.


Hide 9.INSTALL OIL CONTROL VALVE FILTER

Hide 10.INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals, camshaft housing and camshaft bearing caps.


b.

Apply a light coat of engine oil to the camshaft journal, camshaft housing and camshaft bearing caps.


c.

Install the camshaft and No. 2 camshaft to the camshaft housing.


Hide 11.INSTALL CAMSHAFT BEARING CAP

a.
A196897

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


b.
A259149
1.896,1.573 2.052,1.771 0.156,0.198 10 1 1.583,0.188 1.74,0.385 0.156,0.198 10 2 2.458,1.563 2.615,1.76 0.156,0.198 10 3 2.156,0.188 2.313,0.385 0.156,0.198 10 4 2.688,0.177 2.844,0.375 0.156,0.198 10 8 3.021,1.573 3.177,1.771 0.156,0.198 10 7 1.292,1.563 1.448,1.76 0.156,0.198 10 5 1.01,0.188 1.167,0.385 0.156,0.198 10 6 0.135,0.25 0.344,0.427 0.208,0.177 10 10 0.135,0.948 0.292,1.146 0.156,0.198 10 9 0.042,1.74 0.313,1.948 0.271,0.208 10 11

Install the 11 bearing cap bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Make sure that the camshaft rotates smoothly after installing the bearing caps.



Hide 12.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A186390
1.531,0.26 1.969,0.26 0.438,0 1.844,0.615 2.115,0.615 false 0.552,0.802 0.823,0.802 false 2,0.167 2.229,0.375 0.229,0.208 10 *1 2.177,0.531 2.385,0.771 0.208,0.24 10 *2 0.354,0.708 0.604,0.896 0.25,0.188 10 *3 0.219,1.594 0.375,1.813 0.156,0.219 10 *b 0.198,0 0.385,0.24 0.188,0.24 10 *a
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster
*a INCORRECT
*b CORRECT


Check that the valve rocker arms are installed as shown in the illustration.


b.
A311889
0.802,1.146 0.802,0.948 true 2.667,1.865 2.802,1.323 2.802,1.323 3.021,1.323 true 0.823,0.094 1.021,0.292 0.198,0.198 10 false *a 0.74,1.167 0.938,1.365 0.198,0.198 10 false *b 1.271,1.156 1.469,1.354 0.198,0.198 10 false *c 1.26,4.385 1.458,4.583 0.198,0.198 10 false *d 3.063,1.24 3.26,1.438 0.198,0.198 10 false *1
*1 Seal Packing
*a Dashed Line
*b Groove
*c 2.5 to 3.5 mm
*d 3.5 to 4.0 mm


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Apply Seal Packing as Follows:
Area Seal Packing Diameter Application Position
Continuous Line 3.0 to 4.0 mm (0.118 to 0.157 in.) Distance from edge of camshaft housing sub-assembly to center of seal packing: 3.5 to 4.0 mm (0.138 to 0.157 in.)
Dashed Line Distance from outside edge of groove to center of seal packing: 2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.




c.
A196907
2.285,0.376 2.461,0.546 0.177,0.17 10 *b 0.961,0.376 1.138,0.546 0.176,0.17 10 *a 0.672,1.793 0.877,1.968 0.206,0.175 10 *1 1.133,1.332 0.876,1.88 0.876,1.88 2.38,1.321 false
*1 Knock Pin
*a Approximately 17°
*b Approximately 2°


Position the knock pin of the camshaft and No. 2 camshaft as shown in the illustration.


d.
A196884
1.094,0.115 1.198,0.26 0.104,0.146 10 9 1.823,0.552 1.917,0.708 0.094,0.156 10 1 1.552,2 1.646,2.177 0.094,0.177 10 2 1.563,0.115 1.677,0.26 0.115,0.146 10 3 2.313,0.552 2.406,0.708 0.094,0.156 10 4 2.073,1.958 2.188,2.104 0.115,0.146 10 5 2.042,0.115 2.156,0.271 0.115,0.156 10 6 1.313,0.563 1.438,0.719 0.125,0.156 10 7 1.031,1.948 1.125,2.094 0.094,0.146 10 8 2.99,0.896 3.167,1.042 0.177,0.146 10 10 2.375,2 2.552,2.146 0.177,0.146 10 20 0.771,1.896 0.948,2.042 0.177,0.146 10 19 3.135,0.625 3.313,0.771 0.177,0.146 10 18 3.125,1.708 3.302,1.854 0.177,0.146 10 17 3.146,1.052 3.323,1.198 0.177,0.146 10 16 0.74,0.115 0.917,0.26 0.177,0.146 10 15 0.24,1.948 0.417,2.094 0.177,0.146 10 14 0.146,0.646 0.323,0.792 0.177,0.146 10 13 2.469,0.115 2.646,0.26 0.177,0.146 10 12 2.552,1.865 2.729,2.01 0.177,0.146 10 11

Install the camshaft housing, and then install the 20 bearing cap bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Do not apply oil for at least 4 hours after the installation.

·

Do not start the engine for at least 4 hours after the installation.

·

Thoroughly wipe clean any seal packing.




Hide 13.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A284102
0.604,1.302 0.771,1.302 0.771,1.302 1.781,0.854 false 2.698,1.563 2.531,1.563 2.531,1.563 2.042,1.125 false 0.427,1.208 0.74,1.365 0.313,0.156 10 *1 2.76,1.479 3.073,1.635 0.313,0.156 10 *2
*1 Knock Pin Hole
*2 Alignment Mark


Check the camshaft timing gear position.

If the camshaft timing gear is not set to the advanced position, release the lock pin and reset the camshaft timing gear (Refer to the Set Camshaft Timing Gear Assembly procedures).


b.
A196901
1.284,0.128 1.464,0.305 0.181,0.177 10 *1 2.017,0.54 2.185,0.717 0.168,0.177 10 *2 1.983,0.626 1.854,0.626 1.854,0.626 1.639,0.907 false 1.252,0.213 1.123,0.213 1.123,0.213 0.693,0.772 false
*1 Knock Pin Hole
*2 Knock Pin


Align the knock pin of the camshaft with the knock pin hole of the camshaft timing gear and attach the gear to the camshaft.


c.
A196904
2.167,0.844 1.917,0.844 1.917,0.844 1.479,1.073 false 0.823,0.75 0.917,0.75 0.917,0.75 1.125,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 *1 1.802,0.531 2,0.698 0.198,0.167 10 *2 2.188,0.75 2.365,0.917 0.177,0.167 10 *3 1.74,2.031 1.938,2.188 0.198,0.156 10 *c 0.063,0.042 0.25,0.208 0.188,0.167 10 *a 0.063,1.833 0.26,2 0.198,0.167 10 *b
*1 Camshaft Timing Gear
*2 Clearance
*3 Camshaft Flange
*a INCORRECT
*b CORRECT
*c No Clearance


Check that there is no clearance between the camshaft timing gear and camshaft flange.


d.
A265379
1.469,0.225 1.648,0.382 0.178,0.157 10 *a 0.04,1.421 0.219,1.578 0.178,0.157 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear.




Hide 14.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A196902
1.94,0.557 2.124,0.72 0.184,0.163 10 *2 1.278,0.102 1.447,0.265 0.169,0.163 10 *1 1.897,0.652 1.768,0.652 1.768,0.652 1.596,0.931 false 1.226,0.179 1.106,0.179 1.106,0.179 0.668,0.798 false
*1 Knock Pin Hole
*2 Knock Pin


Align the knock pin of the No. 2 camshaft with the knock pin hole of the camshaft timing exhaust gear and attach the gear to the No. 2 camshaft.


b.
A196904
2.167,0.844 1.917,0.844 1.917,0.844 1.479,1.073 false 0.823,0.75 0.917,0.75 0.917,0.75 1.125,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 *1 1.802,0.531 2,0.698 0.198,0.167 10 *2 2.188,0.75 2.365,0.917 0.177,0.167 10 *3 1.74,2.031 1.938,2.188 0.198,0.156 10 *c 0.063,0.042 0.25,0.208 0.188,0.167 10 *a 0.063,1.833 0.26,2 0.198,0.167 10 *b
*1 Camshaft Timing Exhaust Gear
*2 Clearance
*3 Camshaft Flange
*a INCORRECT
*b CORRECT
*c No Clearance


Check that there is no clearance between the camshaft timing exhaust gear and camshaft flange.


c.
A265378
1.602,0.298 1.765,0.45 0.163,0.152 10 *a 0.305,1.902 0.468,2.054 0.163,0.152 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear.




Hide 15.ADD ENGINE OIL

a.
A198199

Add 50 cc (3.1 cu. in.) of engine oil into the oil hole shown in the illustration.

NOTICE:
·

Oil must be added if the lash adjusters were removed.

·

Make sure that the low pressure chamber and oil paths of the lash adjusters are full of engine oil.




Hide 16.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A284109
1.344,0.208 1.802,0.406 0.458,0.198 10 40°

Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.


c.
A293511
0.458,2.875 0.573,2.875 0.573,2.875 0.792,3.104 true 1.781,2.833 1.969,2.833 1.969,2.833 2.604,3.104 true 2.469,1.042 2.573,0.479 2.573,0.479 2.76,0.479 true 1.052,1.021 1.021,0.448 1.021,0.448 1.177,0.448 true 0.292,2.771 0.604,2.927 0.313,0.156 10 *1 1.229,0.354 1.542,0.51 0.313,0.156 10 *a 2.802,0.417 3.115,0.573 0.313,0.156 10 *b 1.594,2.729 1.906,2.885 0.313,0.156 10 *1 3.021,3.677 3.219,3.854 0.198,0.177 10 A 1.354,3.563 1.552,3.74 0.198,0.177 10 A
*1 Timing Mark
*a Approximately 7°
*b Approximately 32°


Check that the timing marks of the camshaft timing gears are as shown in the illustration.

HINT:

"A" is not a timing mark.



d.

Remove the crankshaft pulley bolt.


Hide 17.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 18.INSTALL CHAIN SUB-ASSEMBLY

a.

Place the chain onto the camshaft timing gears and crankshaft timing sprocket.

HINT:
·

Make sure the mark plate of the chain faces away from the engine.

·

It is not necessary to install the chain to the teeth of the gears and sprocket.




b.
A196871
2.664,0.148 2.818,0.309 0.154,0.161 10 *1 2.642,0.234 2.525,0.236 2.525,0.236 2.134,0.687 false 1.457,1.315 1.62,1.485 0.163,0.17 10 *2 1.661,1.4 1.764,1.4 1.764,1.4 2.066,1.174 false
*1 Mark Plate
*2 Timing Mark


Align the mark plate (yellow or gold) of the chain with the timing mark of the camshaft timing exhaust gear and install the chain to the camshaft timing exhaust gear.


c.
A196872
0.938,1.021 1.094,1.021 1.094,1.021 1.302,1.198 true 1.833,0.25 1.719,0.25 1.719,0.25 1.521,1.219 true 1.854,0.177 2.021,0.344 0.167,0.167 10 false *2 0.729,0.917 0.927,1.104 0.198,0.188 10 true *1
*1 Mark Plate
*2 Timing Mark


Align the mark plate (pink or gold) of the chain with the timing mark of the crankshaft timing sprocket and install the chain to the crankshaft timing sprocket.


d.
A196873

Tie a string above the crankshaft timing sprocket so that the chain is secure.


e.
A196874
1.792,3.323 1.677,3.323 1.677,3.323 0.854,3.604 true 0.844,3.865 1.542,4.042 1.542,4.042 1.656,4.042 true 1.813,3.24 1.969,3.406 0.156,0.167 10 *1 1.698,3.938 1.875,4.125 0.177,0.188 10 *2
*1 Mark Plate
*2 Timing Mark


Using the hexagonal portion of the intake camshaft, rotate the intake camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing gear with the mark plate (yellow or gold) of the chain and install the chain to the camshaft timing gear.

HINT:

Hold the intake camshaft in place with a wrench until the chain tensioner is installed.



f.
A196875

Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain so that the chain tensioner slipper can be installed.

NOTICE:

Make sure the chain is secure.



Hide 19.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 20.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the stopper plate.


Hide 21.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 22.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247
5.969,2.958 6.073,2.958 6.073,2.958 6.219,2.771 false 3.51,5.708 4.635,5.417 4.635,5.417 4.875,5.417 false 1.021,2.833 1.021,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 *a 6.25,0.448 6.563,0.604 0.313,0.156 10 *b 5.781,2.854 6.094,3.01 0.313,0.156 10 *1 4.948,5.323 5.26,5.479 0.313,0.156 10 *2 0.948,3.052 1.26,3.208 0.313,0.156 10 *1 6.688,3.656 6.844,3.854 0.156,0.198 10 A 1.646,2.719 1.802,2.917 0.156,0.198 10 A
*1 Timing Mark *2 Key
*a Approximately 7° *b Approximately 32°



b.

Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.

HINT:

"A" is not a timing mark.



c.

Remove the crankshaft pulley bolt.


Hide 23.INSTALL TIMING CHAIN COVER ASSEMBLY

Hide 27.INSTALL FUEL DELIVERY PIPE

Hide 29.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 30.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 31.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY