Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM3090E _51 Engine / Hybrid System _008396 2AR-FE ENGINE MECHANICAL _0046879 CYLINDER HEAD GASKET A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 25051 2.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 22030 3.REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 23901 4.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 5.DISCONNECT WIRE HARNESS

Hide 23814B 6.REMOVE FUEL DELIVERY PIPE

Hide 11310 10.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 11.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247C09
5.948,2.948 6.052,2.948 6.052,2.948 6.219,2.771 false 3.51,5.708 4.615,5.417 4.615,5.417 4.823,5.417 false 1.021,2.833 1.021,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 *a 6.25,0.448 6.563,0.604 0.313,0.156 10 *b 5.781,2.844 6.094,3 0.313,0.156 10 *1 4.865,5.323 5.177,5.479 0.313,0.156 10 *2 0.969,3.063 1.281,3.219 0.313,0.156 10 *1 6.688,3.656 6.844,3.854 0.156,0.198 10 A 1.646,2.719 1.802,2.917 0.156,0.198 10 A
*1 Timing Mark *2 Key
*a Approximately 7° *b Approximately 32°


HINT:

"A" is not a timing mark.



b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 13566B 12.REMOVE TIMING CHAIN GUIDE

a.
A196878

Remove the bolt and timing chain guide.


Hide 13540 13.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196879C09
2.667,0.698 2.406,0.698 2.406,0.698 2.25,1.042 true 1.417,0.479 1.583,0.479 1.583,0.479 1.906,1.073 true 2.698,0.604 2.875,0.76 0.177,0.156 10 *2 1.229,0.396 1.396,0.552 0.167,0.156 10 *1
*1 Stopper Plate
*2 Plunger


Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the tensioner.


b.
A196880C08
1.688,1.948 1.406,1.708 1.406,1.708 1.25,1.708 true 1.063,1.615 1.24,1.771 0.177,0.156 10 *1
*1 Pin


Move the stopper plate clockwise to set the lock, and then insert a pin into the stopper plate hole.


c.
A196877

Remove the 2 bolts, No. 1 chain tensioner and gasket.


Hide 13559 14.REMOVE CHAIN TENSIONER SLIPPER

a.
A196876

Remove the bolt and chain tensioner slipper.


Hide 13506 15.REMOVE CHAIN SUB-ASSEMBLY

Hide 13561 16.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A196868

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13050 17.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A265376C06
1.411,0.255 1.624,0.428 0.213,0.173 10 *a 0.07,1.364 0.284,1.537 0.213,0.173 10 *b
*a Hold
*b Turn


Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing gear.

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear.




Hide 13070A 18.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A265377C06
1.599,0.228 1.782,0.433 0.183,0.205 10 *a 0.268,1.795 0.451,2.0 0.183,0.205 10 *b
*a Hold
*b Turn


Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the bolt and camshaft timing exhaust gear.

NOTICE:
·

Be careful not to damage the cylinder head or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear.




Hide 11103 19.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A259142N07
2.385,1.906 2.542,2.104 0.156,0.198 10 1 0.729,1.917 0.885,2.115 0.156,0.198 10 2 3.156,0.406 3.313,0.604 0.156,0.198 10 3 3.135,1.75 3.292,1.948 0.156,0.198 10 4 3.25,1.052 3.406,1.25 0.156,0.198 10 5 0.469,0.021 0.625,0.219 0.156,0.198 10 6 0.25,2 0.438,2.177 0.188,0.177 10 7 0.042,0.875 0.198,1.073 0.156,0.198 10 8 2.604,0.042 2.76,0.24 0.156,0.198 10 9 2.771,1.865 3.083,2.063 0.313,0.198 10 10 2.406,0.625 2.719,0.823 0.313,0.198 10 11 0.958,0.042 1.271,0.24 0.313,0.198 10 12 0.917,1.896 1.229,2.094 0.313,0.198 10 13 0.688,0.625 1,0.823 0.313,0.198 10 14 2.052,0.031 2.365,0.229 0.313,0.198 10 15 2.083,1.896 2.396,2.094 0.313,0.198 10 16 1.833,0.625 2.146,0.823 0.313,0.198 10 17 1.51,0.031 1.823,0.229 0.313,0.198 10 18 1.5,1.906 1.813,2.104 0.313,0.198 10 19 1.26,0.615 1.573,0.813 0.313,0.198 10 20

Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.


b.
A196899

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.


HINT:

Tape the screwdriver tip before use.



Hide 20.REMOVE CAMSHAFT BEARING CAP

a.
A259149N06
0.115,1.792 0.271,1.99 0.156,0.198 10 1 0.167,0.271 0.323,0.469 0.156,0.198 10 2 0.135,0.969 0.292,1.167 0.156,0.198 10 3 2.688,0.167 2.844,0.365 0.156,0.198 10 4 3.031,1.573 3.188,1.771 0.156,0.198 10 5 1.01,0.177 1.167,0.375 0.156,0.198 10 6 1.333,1.563 1.49,1.76 0.156,0.198 10 7 2.156,0.177 2.313,0.375 0.156,0.198 10 8 2.479,1.573 2.635,1.771 0.156,0.198 10 9 1.542,0.198 1.781,0.396 0.24,0.198 10 10 1.875,1.573 2.115,1.771 0.24,0.198 10 11

Remove the 11 bearing cap bolts in the sequence shown in the illustration.


b.

Remove the 5 camshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 21.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 22.REMOVE NO. 1 CAMSHAFT BEARING

Hide 13511 23.REMOVE CAMSHAFT

a.

Remove the camshaft and No. 2 camshaft.


Hide 11821 24.REMOVE NO. 2 CAMSHAFT BEARING

Hide 13801 25.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 valve rocker arms from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 26.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 27.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 28.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A284098N02
0.552,1.656 0.708,1.854 0.156,0.198 10 1 2.406,0.302 2.563,0.5 0.156,0.198 10 2 0.583,0.302 0.74,0.5 0.156,0.198 10 3 1.021,1.667 1.177,1.865 0.156,0.198 10 5 2.438,1.667 2.594,1.865 0.156,0.198 10 4 1.948,0.302 2.104,0.5 0.156,0.198 10 6 1.042,0.281 1.198,0.479 0.156,0.198 10 7 1.948,1.677 2.104,1.875 0.156,0.198 10 8 1.5,0.292 1.646,0.479 0.146,0.188 10 9 1.469,1.688 1.708,1.865 0.24,0.177 10 10

Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop washers into the cylinder head.

·

Head warpage or cracking could result from removing bolts in an incorrect order.



HINT:

Be sure to keep the removed parts separate for each installation position.



b.

Remove the cylinder head.


Hide 11115 29.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block.


Hide 11101A 30.INSPECT CYLINDER HEAD BOLT

Hide 11101 31.INSPECT CYLINDER HEAD SUB-ASSEMBLY