The headlight leveling ECU receives signals indicating the height of the vehicle from the rear height control sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2416 | Height Control Sensor Malfunction | ·
Malfunction in the rear height control sensor. ·
Open or short in the rear height control sensor circuit |
·
Rear height control sensor sub-assembly LH ·
Harness or connector ·
Headlight leveling ECU assembly |
| B241A | Rear Height Control Sensor | ·
Malfunction in the rear height control sensor. ·
Open or short in the rear height control sensor circuit |
·
Rear height control sensor sub-assembly LH ·
Harness or connector ·
Headlight leveling ECU assembly |
After replacing the headlight leveling ECU and rear height control sensor, initialization of the ECU is necessary.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION
Clear the DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2416 or B241A output does not occur |
| DTC B2416 or B241A output occurs |
DTC B2416 or B241A output does not occur
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B2416 or B241A output occurs
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Height Sens Pw Supply Val | Rear height control sensor power supply value | 0 to 5 V | Approximately 5.0 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value | 0 to 5 V | Approximately 2.5 V (When vehicle level) | The value becomes larger when the front of the vehicle tilts up. |
| Tester Display |
|---|
| Height Sens Pw Supply Val |
| Rr Height Sens Signal Val |
The display is as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A67 headlight leveling ECU connector.
Disconnect the O1*1 or O2*2 rear height control sensor connector.
*1: for 4WD/AWD
*2: for 2WD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-12 (SBR) - O1-3 (SHB) | Always | Below 1 Ω |
| A67-19 (SHRL) - O1-2 (SHRR) | Always | Below 1 Ω |
| A67-21 (SGR) - O1-1 (SHG) | Always | Below 1 Ω |
| A67-12 (SBR) - Body ground | Always | 10 kΩ or higher |
| A67-19 (SHRL) - Body ground | Always | 10 kΩ or higher |
| A67-21 (SGR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-12 (SBR) - O2-3 (SHB) | Always | Below 1 Ω |
| A67-19 (SHRL) - O2-2 (SHRR) | Always | Below 1 Ω |
| A67-21 (SGR) - O2-1 (SHG) | Always | Below 1 Ω |
| A67-12 (SBR) - Body ground | Always | 10 kΩ or higher |
| A67-19 (SHRL) - Body ground | Always | 10 kΩ or higher |
| A67-21 (SGR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear height control sensor.
Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL
Inspect the rear height control sensor.
Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG