Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.04
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside ECM

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

C299919E01
0.188,0.115 1.875,0.313 1.688,0.198 12 false for 2AR-FE: 1.521,0.781 3.208,0.979 1.688,0.198 10 false 1 1.51,1.302 3.198,1.5 1.688,0.198 10 false 2 0.365,1.813 2.052,2.01 1.688,0.198 10 false N27 0.365,1.938 2.5,2.177 2.135,0.24 10 false No. 3 CAN Junction Connector 5.177,1.438 5.865,1.708 0.688,0.271 10 false A62 5.177,0.917 5.865,1.188 0.688,0.271 10 false A62 5.542,0.813 6.229,1.083 0.688,0.271 10 false CANH 5.552,1.563 6.24,1.833 0.688,0.271 10 false CANL 5.219,1.25 5.906,1.521 0.688,0.271 10 false 26 5.229,0.708 5.917,0.979 0.688,0.271 10 false 13 5.177,2.458 5.865,2.729 0.688,0.271 10 false A62 5.156,3.01 5.844,3.281 0.688,0.271 10 false A62 5.177,3.573 5.865,3.844 0.688,0.271 10 false A62 5.177,4.125 5.865,4.396 0.688,0.271 10 false A62 5.583,4.125 6.271,4.396 0.688,0.271 10 false MREL 5.583,3.563 6.271,3.833 0.688,0.271 10 false +B2 5.552,3.01 6.24,3.281 0.688,0.271 10 false +B 5.573,2.448 6.26,2.719 0.688,0.271 10 false BATT 5.25,2.26 6.938,2.458 1.688,0.198 10 false 1 5.271,2.802 6.958,3 1.688,0.198 10 false 2 5.25,3.354 6.938,3.552 1.688,0.198 10 false 3 5.219,4.469 6.906,4.667 1.688,0.198 10 false 37 5.177,4.667 5.865,4.938 0.688,0.271 10 false A62 5.573,4.667 6.26,4.938 0.688,0.271 10 false IGSW 5.219,3.917 6.906,4.115 1.688,0.198 10 false 46 5.781,7.385 6.469,7.656 0.688,0.271 10 false ECM 5.177,5.229 5.865,5.5 0.688,0.271 10 false B77 5.177,5.781 5.865,6.052 0.688,0.271 10 false B77 5.188,6.344 5.875,6.615 0.688,0.271 10 false B77 5.177,6.823 5.865,7.094 0.688,0.271 10 false B77 5.583,6.813 6.271,7.083 0.688,0.271 10 false ME01 5.573,6.323 6.26,6.594 0.688,0.271 10 false E01 5.583,5.781 6.271,6.052 0.688,0.271 10 false E02 5.573,5.229 6.26,5.5 0.688,0.271 10 false E1 5.219,5.031 5.906,5.302 0.688,0.271 10 false 16 5.219,5.573 5.906,5.844 0.688,0.271 10 false 49 5.219,6.135 5.906,6.406 0.688,0.271 10 false 50 5.219,6.615 5.906,6.885 0.688,0.271 10 false 58 1.542,2.427 2.552,2.979 1.01,0.552 10 false from Battery 3.271,2.302 4.281,2.854 1.01,0.552 10 false EFI-MAIN NO.1 0.677,3 2.51,3.625 1.833,0.625 10 false from EFI-MAIN NO.1 Relay 0.833,4.083 2.667,4.708 1.833,0.625 10 false to EFI-MAIN NO.1 Relay 1.406,4.656 3.24,5.281 1.833,0.625 10 false from IG2 Relay 3.604,4.521 5.438,5.146 1.833,0.625 10 false IGN

C299920E02
0.323,1.813 0.781,2.01 0.458,0.198 10 false N27 0.313,1.979 4.594,2.177 4.281,0.198 10 false No. 3 CAN Junction Connector 1.552,2.469 3.385,2.667 1.833,0.198 10 false from Battery 0.667,3.01 4.333,3.208 3.667,0.198 10 false from EFI-MAIN NO.1 Relay 0.813,4.115 4.479,4.313 3.667,0.198 10 false to EFI-MAIN NO.1 Relay 1.417,4.677 3.563,4.875 2.146,0.198 10 false from IG2 Relay 1.531,0.792 1.688,0.99 0.156,0.198 10 false 1 1.542,1.313 1.698,1.51 0.156,0.198 10 false 2 5.188,0.917 5.646,1.115 0.458,0.198 10 false A62 5.188,1.448 5.646,1.646 0.458,0.198 10 false A62 5.177,2.469 5.635,2.667 0.458,0.198 10 false A62 5.167,3.021 5.625,3.219 0.458,0.198 10 false A62 5.188,3.573 5.646,3.771 0.458,0.198 10 false A62 5.177,4.115 5.635,4.313 0.458,0.198 10 false A62 5.188,4.677 5.646,4.875 0.458,0.198 10 false A62 5.177,5.24 5.635,5.438 0.458,0.198 10 false B75 5.177,5.792 5.635,5.99 0.458,0.198 10 false B75 5.188,6.344 5.646,6.542 0.458,0.198 10 false B75 5.188,6.823 5.646,7.021 0.458,0.198 10 false B75 5.219,0.708 5.531,0.906 0.313,0.198 10 false 13 0.083,0.063 2.104,0.302 2.021,0.24 12 false for 3ZR-FAE, 3ZR-FE: 3.198,2.323 5.188,2.521 1.99,0.198 10 false EFI-MAIN NO.2 3.406,2.875 4.635,3.073 1.229,0.198 10 false EFI-NO.1 3.583,4.531 4.042,4.729 0.458,0.198 10 false IGN 5.573,0.813 6.188,1.01 0.615,0.198 10 false CANH 5.563,1.573 6.177,1.771 0.615,0.198 10 false CANL 5.563,2.469 6.177,2.667 0.615,0.198 10 false BATT 5.573,2.99 5.885,3.188 0.313,0.198 10 false +B 5.563,3.573 6.021,3.771 0.458,0.198 10 false +B2 5.563,4.125 6.177,4.323 0.615,0.198 10 false MREL 5.573,4.667 6.188,4.865 0.615,0.198 10 false IGSW 5.573,5.24 5.885,5.438 0.313,0.198 10 false E1 5.573,5.781 6.031,5.979 0.458,0.198 10 false E02 5.573,6.354 6.031,6.552 0.458,0.198 10 false E01 5.552,6.802 6.167,7 0.615,0.198 10 false ME01 5.844,7.333 6.302,7.531 0.458,0.198 10 false ECM 5.229,1.25 5.542,1.448 0.313,0.198 10 false 26 5.26,2.26 5.417,2.458 0.156,0.198 10 false 1 5.281,2.802 5.438,3 0.156,0.198 10 false 2 5.271,3.365 5.427,3.563 0.156,0.198 10 false 3 5.229,3.927 5.542,4.125 0.313,0.198 10 false 46 5.219,4.458 5.531,4.656 0.313,0.198 10 false 37 5.208,5.021 5.521,5.219 0.313,0.198 10 false 16 5.219,5.573 5.531,5.771 0.313,0.198 10 false 21 5.219,6.146 5.531,6.344 0.313,0.198 10 false 51 5.219,6.615 5.531,6.813 0.313,0.198 10 false 59

C299919E02
0.188,0.115 4.021,0.438 3.833,0.323 12 false for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF: 1.521,0.781 3.208,0.979 1.688,0.198 10 false 1 1.51,1.302 3.198,1.5 1.688,0.198 10 false 2 0.365,1.813 2.052,2.01 1.688,0.198 10 false N27 0.365,1.938 2.5,2.177 2.135,0.24 10 false No. 3 CAN Junction Connector 5.177,1.438 5.865,1.708 0.688,0.271 10 false A61 5.177,0.917 5.865,1.188 0.688,0.271 10 false A61 5.542,0.813 6.229,1.083 0.688,0.271 10 false CANH 5.552,1.563 6.24,1.833 0.688,0.271 10 false CANL 5.25,1.25 5.938,1.521 0.688,0.271 10 false 6 5.24,0.708 5.927,0.979 0.688,0.271 10 false 7 5.177,2.458 5.865,2.729 0.688,0.271 10 false A61 5.167,3.01 5.854,3.281 0.688,0.271 10 false A61 5.177,3.573 5.865,3.844 0.688,0.271 10 false A61 5.177,4.125 5.865,4.396 0.688,0.271 10 false A61 5.583,4.125 6.271,4.396 0.688,0.271 10 false MREL 5.583,3.563 6.271,3.833 0.688,0.271 10 false +B2 5.552,3.01 6.24,3.281 0.688,0.271 10 false +B 5.573,2.448 6.26,2.719 0.688,0.271 10 false BATT 5.25,2.26 6.938,2.458 1.688,0.198 10 false 2 5.271,2.802 6.958,3 1.688,0.198 10 false 1 5.219,3.365 6.906,3.563 1.688,0.198 10 false 20 5.219,4.458 6.906,4.656 1.688,0.198 10 false 25 5.177,4.667 5.865,4.938 0.688,0.271 10 false A61 5.573,4.667 6.26,4.938 0.688,0.271 10 false IGSW 5.219,3.917 6.906,4.115 1.688,0.198 10 false 45 5.781,7.385 6.469,7.656 0.688,0.271 10 false ECM 5.177,5.229 5.865,5.5 0.688,0.271 10 false B76 5.177,5.781 5.865,6.052 0.688,0.271 10 false B76 5.188,6.344 5.875,6.615 0.688,0.271 10 false B76 5.177,6.823 5.865,7.094 0.688,0.271 10 false B76 5.583,6.813 6.271,7.083 0.688,0.271 10 false ME01 5.573,6.323 6.26,6.594 0.688,0.271 10 false E01 5.583,5.781 6.271,6.052 0.688,0.271 10 false E02 5.573,5.229 6.26,5.5 0.688,0.271 10 false E1 5.188,5.021 5.875,5.292 0.688,0.271 10 false 109 5.219,5.573 5.906,5.844 0.688,0.271 10 false 44 5.208,6.135 5.896,6.406 0.688,0.271 10 false 45 5.219,6.615 5.906,6.885 0.688,0.271 10 false 84 1.542,2.427 2.552,2.979 1.01,0.552 10 false from Battery 3.427,2.302 4.438,2.854 1.01,0.552 10 false EFI NO.3 0.677,3 2.51,3.625 1.833,0.625 10 false from EFI-MAIN NO.1 Relay 0.833,4.083 2.667,4.708 1.833,0.625 10 false to EFI-MAIN NO.1 Relay 1.406,4.656 3.24,5.281 1.833,0.625 10 false from IG2 Relay 3.604,4.521 5.438,5.146 1.833,0.625 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Drive the vehicle for 50 seconds at a speed of 20 km/h (12 mph).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C277468C01
1.573,0.313 1.99,0.573 0.417,0.26 0.552,2.354 0.969,2.615 0.417,0.26 2.938,0.729 2.74,0.729 2.74,0.729 2.51,1.125 true 2.958,1.375 2.771,1.375 2.771,1.375 2.51,1.219 true 2.74,2.719 2.552,2.719 2.552,2.719 2.094,3.135 true 2.406,2.521 2.219,2.521 2.219,2.521 2,3.135 true 2.073,0.365 2.385,0.521 0.313,0.156 10 *A 1.031,2.396 1.344,2.552 0.313,0.156 10 *B 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 2.979,0.656 3.427,0.833 0.448,0.177 10 CANH 3,1.302 3.427,1.458 0.427,0.156 10 CANL 1.646,0.365 2.26,0.563 0.615,0.198 10 A62 0.625,2.406 1.24,2.604 0.615,0.198 10 A61 2.438,2.448 2.865,2.604 0.427,0.156 10 CANL 2.792,2.656 3.24,2.833 0.448,0.177 10 CANH
*A for 2AR-FE, 3ZR-FAE, 3ZR-FE
*B for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FAE, 3ZR-FE
Tester Connection Connector Specified Condition
A62-13 (CANH) - A62-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
Tester Connection Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

for 2AR-FE:

C229008C20
1.656,0.51 2.073,0.76 0.417,0.25 5.094,0.542 5.51,0.792 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 1.552,1.375 1.167,0.667 1.167,0.667 0.917,0.667 true 1.667,1.375 1.333,0.417 1.333,0.417 1,0.417 true 1.833,1.615 1.333,2.25 1.333,2.25 1.083,2.25 true 4.844,1.406 4.417,0.75 4.417,0.75 4.167,0.75 true 5.104,1.49 4.75,0.5 4.75,0.5 4.5,0.5 true 5.177,1.521 4.75,2.25 4.75,2.25 4.5,2.25 true 5.865,1.5 6.25,2.25 6.25,2.25 6.5,2.25 true 2.615,1.635 2.854,2.292 2.854,2.292 3.104,2.292 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.344,0.844 0.75,1.083 0.406,0.24 10 false BATT 0.667,0.583 1.073,0.823 0.406,0.24 10 false +B 0.677,0.344 1.083,0.583 0.406,0.24 10 false +B2 0.667,2.167 1.167,2.417 0.5,0.25 10 false IGSW 1.729,0.552 2.135,0.792 0.406,0.24 10 false A62 3.917,0.667 4.323,0.906 0.406,0.24 10 false E1 4.177,0.427 4.583,0.667 0.406,0.24 10 false E02 4.177,2.177 4.583,2.417 0.406,0.24 10 false E01 6.583,2.177 6.99,2.417 0.406,0.24 10 false ME01 5.177,0.583 5.583,0.823 0.406,0.24 10 false B77 3.146,2.208 3.646,2.458 0.5,0.25 10 false MREL
*a Front view of wire harness connector
(to ECM)
- -


i.

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (BATT) - Body ground Always 11 to 14 V
A62-2 (+B) - Body ground Battery positive (+) voltage applied to terminal A62-46 (MREL) 11 to 14 V
A62-3 (+B2) - Body ground Battery positive (+) voltage applied to terminal A62-46 (MREL) 11 to 14 V
A62-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-16 (E1) - Body ground Always Below 1 Ω
B77-49 (E02) - Body ground Always Below 1 Ω
B77-50 (E01) - Body ground Always Below 1 Ω
B77-58 (ME01) - Body ground Always Below 1 Ω




c.

for 3ZR-FAE, 3ZR-FE:

C229008C24
1.656,0.51 2.073,0.76 0.417,0.25 5.094,0.542 5.51,0.792 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 1.552,1.375 1.167,0.667 1.167,0.667 0.917,0.667 true 1.667,1.375 1.333,0.417 1.333,0.417 1,0.417 true 1.833,1.615 1.333,2.25 1.333,2.25 1.083,2.25 true 4.844,1.406 4.417,0.75 4.417,0.75 4.167,0.75 true 5.25,1.5 4.75,2.25 4.75,2.25 4.5,2.25 true 5.948,1.5 6.25,2.25 6.25,2.25 6.5,2.25 true 5.24,1.406 4.75,0.5 4.75,0.5 4.5,0.5 true 2.615,1.635 2.875,2.271 2.875,2.271 3.083,2.271 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.344,0.844 0.75,1.083 0.406,0.24 10 false BATT 0.667,0.583 1.073,0.823 0.406,0.24 10 false +B 0.677,0.344 1.083,0.583 0.406,0.24 10 false +B2 0.667,2.167 1.167,2.417 0.5,0.25 10 false IGSW 1.729,0.552 2.135,0.792 0.406,0.24 10 false A62 3.917,0.667 4.323,0.906 0.406,0.24 10 false E1 4.177,0.427 4.583,0.667 0.406,0.24 10 false E02 4.177,2.177 4.583,2.417 0.406,0.24 10 false E01 6.583,2.177 6.99,2.417 0.406,0.24 10 false ME01 5.177,0.583 5.583,0.823 0.406,0.24 10 false B75 3.135,2.208 3.635,2.458 0.5,0.25 10 false MREL
*a Front view of wire harness connector
(to ECM)
- -


i.

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (BATT) - Body ground Always 11 to 14 V
A62-2 (+B) - Body ground Battery positive (+) voltage applied to terminal A62-46 (MREL) 11 to 14 V
A62-3 (+B2) - Body ground Battery positive (+) voltage applied to terminal A62-46 (MREL) 11 to 14 V
A62-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-16 (E1) - Body ground Always Below 1 Ω
B75-21 (E02) - Body ground Always Below 1 Ω
B75-51 (E01) - Body ground Always Below 1 Ω
B75-59 (ME01) - Body ground Always Below 1 Ω




d.

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF:

C234869C04
0.323,1.354 0.792,1.625 0.469,0.271 3.719,0.542 4.188,0.813 0.469,0.271 1.344,0.719 1.625,0.719 1.625,0.719 1.865,1.198 true 1.479,0.479 1.76,0.479 1.76,0.479 1.958,1.188 true 4.885,0.719 5.146,0.719 5.146,0.719 5.49,1.323 true 1.26,2.052 1.542,2.052 1.542,2.052 1.865,1.427 true 2.708,0.813 2.5,0.813 2.5,0.813 2.344,1.375 true 5.917,0.521 5.708,0.521 5.708,0.521 5.583,1.323 true 6.125,2.188 5.823,2.188 5.823,2.188 5.667,1.813 true 4.948,2.292 5.219,2.292 5.219,2.292 5.49,1.677 true 2.885,2.229 2.688,2.229 2.688,2.229 2.438,1.719 true 0.438,1.406 0.729,1.583 0.292,0.177 10 false A61 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 1.115,0.656 1.375,0.854 0.26,0.198 10 false +B 1.125,0.417 1.552,0.583 0.427,0.167 10 false BATT 2.75,0.74 3.615,0.906 0.865,0.167 10 false IGSW 4.604,0.656 5.469,0.823 0.865,0.167 10 false E02 0.948,1.99 1.458,2.156 0.51,0.167 10 false +B2 5.979,0.438 6.844,0.604 0.865,0.167 10 false E01 4.542,2.219 5.406,2.385 0.865,0.167 10 false ME01 6.177,2.104 7.042,2.271 0.865,0.167 10 false E1 3.823,0.594 4.115,0.771 0.292,0.177 10 false B76 2.927,2.167 3.792,2.333 0.865,0.167 10 false MREL
*a Front view of wire harness connector
(to ECM)
- -


i.

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A61-2 (BATT) - Body ground Always 11 to 14 V
A61-1 (+B) - Body ground Battery positive (+) voltage applied to terminal A61-45 (MREL) 11 to 14 V
A61-20 (+B2) - Body ground Battery positive (+) voltage applied to terminal A61-45 (MREL) 11 to 14 V
A61-25 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-44 (E02) - Body ground Always Below 1 Ω
B76-45 (E01) - Body ground Always Below 1 Ω
B76-84 (ME01) - Body ground Always Below 1 Ω
B76-109 (E1) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR