While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Refer to DTC P0617 (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| NG (for CVT Models) | A |
| NG (for Manual Transaxle Models) | B |
| OK | C |
A
B
C
Inspect the park/neutral position switch assembly (Click here Drivetrain>K111F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - B36-4 (B) | Always | Below 1 Ω |
| G82-5 (STAR) - B75-63 (NSW) | Always | Below 1 Ω |
| G82-5 (STAR), B36-4 (B) or B75-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B36-9 (L) - A62-22 (STA) | Always | Below 1 Ω |
| B36-9 (L), 2 (ST relay), A62-22 (STA) or G82-7 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly (Click here Engine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-2 (ST2) - B36-4 (B) | Always | Below 1 Ω |
| G4-2 (ST2) - B75-63 (NSW) | Always | Below 1 Ω |
| G4-2 (ST2), B36-4 (B) or B75-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B36-9 (L) - A62-22 (STA) | Always | Below 1 Ω |
| B36-9 (L), 2 (ST relay) or A62-22 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly (Click here Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - A4-2 | Always | Below 1 Ω |
| G82-5 (STAR) or A4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - F2-2 | Always | Below 1 Ω |
| G82-5 (STAR) or F2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the clutch start switch assembly connector.
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-1 - A62-22 (STA) | Always | Below 1 Ω |
| A4-1, 2 (ST relay), A62-22 (STA) or G82-7 (STA) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-1 - A62-22 (STA) | Always | Below 1 Ω |
| F2-1, 2 (ST relay), A62-22 (STA) or G82-7 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly (Click here Engine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-2 (ST2) - A4-2 | Always | Below 1 Ω |
| G4-2 (ST2) or A4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-2 (ST2) - F2-2 | Always | Below 1 Ω |
| G4-2 (ST2) or F2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the clutch start switch assembly connector.
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-1 - A62-22 (STA) | Always | Below 1 Ω |
| A4-1, 2 (ST relay) or A62-22 (ST2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-1 - A62-22 (STA) | Always | Below 1 Ω |
| F2-1, 2 (ST relay) or A62-22 (ST2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay (Click here Engine / Hybrid System>3ZR-FAE STARTING>RELAY>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly (Click here Engine / Hybrid System>3ZR-FAE STARTING>STARTER>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (ST relay) - B6-1 | Always | Below 1 Ω |
| 3 (ST relay) or B6-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST Relay |
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST relay) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for CVT Models) | A |
| OK (for Manual Transaxle Models) | B |
| NG | C |
A
B
C
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - B36-9 (L) | Always | Below 1 Ω |
| 2 (ST relay) or B36-9 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - A4-1 | Always | Below 1 Ω |
| 2 (ST relay) or A4-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - F2-1 | Always | Below 1 Ω |
| 2 (ST relay) or F2-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG