Home › Engine / Hybrid System › 1AD-FTV ENGINE MECHANICAL › ENGINE UNIT › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008733 1AD-FTV ENGINE MECHANICAL _0049235 ENGINE UNIT A

1AD-FTV ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 11415 1.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to the cylinder block water drain cock sub-assembly.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent



b.

Install the cylinder block water drain cock sub-assembly to the cylinder block sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 12216G 2.INSTALL OIL BAFFLE PLATE

a.

Install the oil baffle plate with the 4 bolts.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


Hide 11115 5.INSTALL CYLINDER HEAD GASKET

Hide 11101 6.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13750 7.INSPECT VALVE LASH ADJUSTER ASSEMBLY

Hide 13750 8.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 9.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13471A 11.INSTALL CRANKSHAFT PULLEY SET CRANKSHAFT KEY

a.

Install the 2 crankshaft pulley set crankshaft keys to the crankshaft.


Hide 13523 12.INSTALL CAMSHAFT TIMING SPROCKET

a.
A271554
1.406,0.208 2.156,0.208 false 0.813,0.156 1.354,0.156 false 1.833,3.313 2.313,3.115 2.313,3.115 2.469,3.115 false 1.229,3.229 1.823,3.229 false 1.698,0.604 2.375,0.604 false 2.427,0.5 2.74,0.656 0.313,0.156 10 *1 2.188,0.104 2.5,0.26 0.313,0.156 10 *2 0.635,0.052 0.948,0.208 0.313,0.156 10 *3 2.5,3.01 2.813,3.167 0.313,0.156 10 *3 1.01,3.115 1.323,3.271 0.313,0.156 10 *2
*1 Hole
*2 Timing Mark
*3 Pink Paint Mark


Install the crankshaft timing sprocket and camshaft timing sprocket to the chain sub-assembly so that the timing marks of the sprockets and paint marks of the chain sub-assembly are aligned.


b.

Install the camshaft timing sprocket to the No. 2 camshaft by fitting the straight pin of the No. 2 camshaft into the hole on the camshaft timing sprocket.


c.

Install the crankshaft timing sprocket to the crankshaft.


d.

While holding the hexagon portion of the No. 2 camshaft, install and uniformly tighten the 4 bolts of the No. 2 camshaft.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 13519 13.INSTALL OIL PUMP DRIVE GEAR

a.

Install the oil pump drive gear to the crankshaft.


Hide 13561 14.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 15.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper.


Hide 13540 16.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A101303
2.129,1.571 2.379,1.772 0.25,0.201 10 *2 0.247,1.786 0.576,1.987 0.329,0.201 10 SST 1.845,1.514 1.974,1.687 1.974,1.687 2.111,1.687 false 2.502,0.213 3.041,0.415 0.539,0.201 10 *1 2.318,0.763 2.356,0.321 2.356,0.321 2.481,0.321 false 0.407,1.786 0.534,1.474 false
*1 Plunger
*2 Stopper Plate


Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

SST
09240-00020  (09242-00200)


c.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


d.

Remove SST.


Hide 11301C 17.INSTALL FRONT CRANKSHAFT OIL SEAL

Hide 11302 18.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13471 19.INSTALL CRANKSHAFT PULLEY

a.

Align the keyway of the crankshaft pulley with the key located on the crankshaft, and then slide the crankshaft pulley into place to install it.


b.
A297923
1.844,1.938 2.365,1.635 2.365,1.635 2.552,1.635 false 0.927,1.063 1.927,0.875 1.927,0.875 2.135,0.875 false 0.76,0.854 1.573,0.417 1.573,0.417 1.75,0.417 false 1.823,0.313 2.281,0.51 0.458,0.198 10 SST 2.198,0.781 2.656,0.979 0.458,0.198 10 SST 2.615,1.552 3.073,1.75 0.458,0.198 10 SST

Using SST, install a new crankshaft pulley bolt.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
300 N*m (3059 kgf*cm, 221 ft.*lbf)


Hide 15104 20.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 15677 21.INSTALL OIL FILTER BRACKET

Hide 15350A 22.INSTALL OIL PRESSURE SWITCHING VALVE ASSEMBLY

Hide 12102A 24.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 11201 25.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23699A 26.INSTALL NOZZLE HOLDER CLAMP SEAT

Hide 12108 27.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 16323 28.INSTALL WATER INLET HOUSING

Hide 89491 29.INSTALL ENGINE OIL LEVEL SENSOR

a.

Install the engine oil level sensor with the 4 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 15781 30.INSTALL NO. 1 OIL COOLER BRACKET

Hide 15710 31.INSTALL OIL COOLER ASSEMBLY

Hide 83520 32.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 16100 33.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 89422C 34.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 11401G 35.INSTALL CRANKSHAFT POSITION SENSOR

a.

Install the crankshaft position sensor with the 2 bolts.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


b.

Attach the clip and connect the crankshaft position sensor harness.


Hide 11301K 36.INSTALL CAMSHAFT POSITION SENSOR

a.

Install the camshaft position sensor with the bolt.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


Hide 23670 37.INSTALL INJECTOR ASSEMBLY

Hide 23762 38.INSTALL NO. 2 NOZZLE LEAKAGE PIPE