Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

STOP fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the indicator in the combination meter is not illuminated in green). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2284
Power Source Control:
·

Stop Light Switch1


ABS/VSC/TRAC:
·

Stop Light SW


-

WIRING DIAGRAM

C279146E01
0.479,0.823 1.365,1.073 0.885,0.25 10 from Battery 0.49,1.552 1.5,1.76 1.01,0.208 10 from Battery 2.74,1 3.198,1.198 0.458,0.198 10 AM2 4.604,0.823 4.917,1.021 0.313,0.198 10 +B 4.354,0.688 4.51,0.885 0.156,0.198 10 2 4.583,1.583 5.198,1.781 0.615,0.198 10 STP1 4.323,1.469 4.635,1.667 0.313,0.198 10 18 4.594,2.458 4.75,2.656 0.156,0.198 10 E 4.313,2.323 4.625,2.521 0.313,0.198 10 11 3.865,1.458 4.021,1.656 0.156,0.198 10 1 2.729,1.458 2.885,1.656 0.156,0.198 10 2 1.823,1.75 2.438,1.948 0.615,0.198 10 STOP 2.688,1.885 3,2.083 0.313,0.198 10 A5 2.667,2.063 3.854,2.479 1.188,0.417 10 Stop Light Switch Assembly 1.844,3.208 3.573,3.406 1.729,0.198 10 : CAN Communication Line 4.125,3.052 4.583,3.25 0.458,0.198 10 G82 4.438,3.052 6.24,3.448 1.802,0.396 10 Certification ECU (Smart Key ECU Assembly) 6.458,2.188 6.917,2.385 0.458,0.198 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH 1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.


Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV (for DPF))
NG (for 2AD-FTV (for CCo))
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG (for 1AD-FTV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FHV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FTV (for DPF))

NG (for 2AD-FTV (for CCo))

NG (for 2AR-FE)

NG (for 3ZR-FAE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 3ZR-FE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C38
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 false *a 2.521,1.74 2.906,1.885 0.385,0.146 10 false E 0.583,1.375 1.031,1.563 0.448,0.188 10 false G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A5 connector from the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-18 (STP1) - A5-1 Always Below 1 Ω
G82-18 (STP1) or A5-1 - Body ground 10 kΩ or higher



c.
B269097C13
0.365,1.75 0.792,1.979 0.427,0.229 0.917,2.74 1.333,2.323 false 0.135,0.177 0.448,0.333 0.313,0.156 10 *a 0.427,1.781 0.906,1.938 0.479,0.156 10 G82 0.677,2.771 1.156,2.927 0.479,0.156 10 STP1
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Reconnect the A5 connector from the stop light switch assembly.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-18 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR