Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY(for RHD) › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049513 HOOD LOCK CONTROL CABLE ASSEMBLY(for RHD) A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY(for RHD)  INSTALLATION  


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B277362C05
1.542,1.231 1.729,1.392 0.187,0.162 10 *1 1.751,1.326 2.492,1.326 false
Text in Illustration
*1 String


Tie the string that was passed through the engine compartment room to the end of the hood lock control cable assembly as shown in the illustration.

HINT:

Use a length of string long enough to pass through the engine compartment room.



b.

Pass the hood lock control cable assembly through the vehicle body, and then attach each clamp.


c.

Untie the string from the hood lock control cable assembly.

B338125C04
5.313,1.229 5.979,1.49 true 3.708,0.844 4.208,1.188 true 3.375,0.75 3.083,1.229 true 2.188,0.438 1.573,0.438 true 1.219,1.75 0.531,1.615 true 1.021,3.813 0.51,3.813 true 1.844,5.396 1.448,5.063 true 2.99,1.271 3.302,1.427 0.313,0.156 10 *1 4.229,1.115 4.542,1.271 0.313,0.156 10 *2 6,1.427 6.313,1.583 0.313,0.156 10 *1 1.427,0.354 1.74,0.51 0.313,0.156 10 *1 0.385,1.531 0.698,1.688 0.313,0.156 10 *1 0.344,3.74 0.656,3.896 0.313,0.156 10 *1 1.885,5.333 2.198,5.49 0.313,0.156 10 *1
Text in Illustration
*1 Hood Lock Control Cable *2 Stopper



Hide 53510 2.INSTALL HOOD LOCK ASSEMBLY

a.

Apply MP grease to the sliding parts of the hood lock assembly.


b.

Connect the hood lock control cable assembly to the hood lock assembly.


c.

Install the hood lock assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

w/ Engine Hood Courtesy Switch:

Connect the connector.


Hide 53629 3.INSTALL HOOD LOCK CONTROL CABLE COVER (w/ Cover)

a.

Attach the guide and clip to install the hood lock control cable cover.


Hide 53601 4.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Connect the hood lock control cable assembly to the hood lock control lever assembly.


b.

Attach the 3 claws to install the hood lock control lever assembly.


Hide 55545 5.INSTALL FUSE BOX OPENING COVER

Hide 62111C 6.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 7.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 55701J 8.INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

Hide 53388D 9.INSTALL HOOD TO FRONT FENDER SEAL RH

a.
B340664

Attach the 3 clips to install the hood to front fender seal RH.


b.

Install the clip.


Hide 53389B 10.INSTALL HOOD TO FRONT FENDER SEAL LH

HINT:

Use the same procedure described for the RH side.


Hide 53216A 11.INSTALL UPPER RADIATOR SUPPORT (w/ Cover)

Hide 12.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 16681 13.INSTALL UPPER RADIATOR AIR GUIDE PLATE

Hide 52029 14.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

Hide 16.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52085 17.INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY

Hide 52119A 18.INSTALL FRONT BUMPER COVER

Hide 53896B 19.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 20.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

HINT:

Use the same procedure described for the LH side.


Hide 22.ADJUST FOG LIGHT AIMING (w/ Fog Light)