Home › Engine / Hybrid System › 1AD-FTV COOLING › RADIATOR › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008374 1AD-FTV COOLING _0050232 RADIATOR A

1AD-FTV COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16711 1.INSTALL FAN SHROUD

a.

Install the fan shroud with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17940D 2.INSTALL INTERCOOLER ASSEMBLY

Hide 16535 3.INSTALL LOWER RADIATOR SUPPORT

Hide 16572D 4.INSTALL NO. 2 RADIATOR HOSE

a.

Install the No. 2 radiator hose to the radiator assembly, and slide the clamp to secure the hose.

HINT:
A295982C01
0.813,0.104 1.125,0.26 0.313,0.156 10 false *a 1.177,0.729 1.49,0.885 0.313,0.156 10 false 90°
*a Top


Position the clamp as illustrated.



Hide 16057 5.INSTALL RADIATOR HOSE SUB-ASSEMBLY

A297505C01
0.833,0.094 1.146,0.25 0.313,0.156 10 false *a 1.063,2.51 1.375,2.667 0.313,0.156 10 false *b 0.76,0.865 1.063,1.01 0.302,0.146 10 false 180° 1.594,1.979 1.906,2.135 0.313,0.156 10 false *a 0.333,0.583 0.646,0.74 0.313,0.156 10 false *b 1.604,3.063 1.906,3.208 0.302,0.146 10 false 180°
*a Top
*b LH Side


a.

Install the radiator hose sub-assembly to the radiator assembly and slide the 2 clamps to secure the hose.

HINT:

Position the clamps as illustrated.



b.

Attach the 2 clamps to the fan shroud.


Hide 17362B 6.INSTALL NO. 2 AIR TUBE

a.

Install the No. 2 air tube to the intercooler assembly with the bolt.

NOTICE:

Before installation, remove any oil residue from the inside of the No. 2 air tube and intercooler assembly.


Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.
A295984C01
3.115,0.219 3.427,0.375 0.313,0.156 10 false *a 2.958,0.729 3.208,0.917 0.25,0.188 10 false 90°
*a LH Side


Tighten the hose clamp.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

HINT:

Position the clamp as illustrated.



Hide 25770A 7.INSTALL NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

a.
A295983C01
0.688,2.146 1,2.302 0.313,0.156 10 false *a 0.958,3.042 1.271,3.198 0.313,0.156 10 false 90° 3,3.042 3.313,3.198 0.313,0.156 10 false 180° 2.729,2.198 3.042,2.354 0.313,0.156 10 false *a
*a Top


Attach the 4 clamps to the fan shroud and No. 2 air tube.


b.

Install the No. 2 vacuum transmitting hose assembly to the intercooler assembly and No. 2 air hose and 2 clips to securethe hose.

HINT:

Position the clips as illustrated.



Hide 88460 8.INSTALL COOLER CONDENSER ASSEMBLY

a.

Install the cooler condenser assembly.


Hide 16533 9.INSTALL NO. 2 RADIATOR SUPPORT

a.

Install the 2 No. 2 radiator supports with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16400 10.INSTALL RADIATOR ASSEMBLY

a.

Install the 2 cushions.


b.

Insert the radiator assembly.


Hide 17342F 12.INSTALL INTERCOOLER AIR HOSE

NOTICE:

Before installation, remove any oil residue from the inside of the intercooler air hose.


a.
A300888C01
0.865,2.26 1.177,2.417 0.313,0.156 10 false *a 0.188,2.656 0.5,2.813 0.313,0.156 10 false *b 0.74,3.167 1.052,3.323 0.313,0.156 10 false 90° 0.917,2.927 1.229,3.083 0.313,0.156 10 false 45° 2.76,0.115 3.073,0.271 0.313,0.156 10 false *a 2.052,0.625 2.365,0.781 0.313,0.156 10 false *b 3.031,0.281 3.344,0.438 0.313,0.156 10 false 90°
*a Top
*b LH Side


Install the intercooler air hose to the No. 1 air tube and intercooler assembly and tighten the 2 hose clamps.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

HINT:

Position the hose clamps as illustrated.



Hide 16057 14.CONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 53216A 15.INSTALL UPPER RADIATOR SUPPORT

a.

Install the upper radiator support with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 17.CONNECT WIRE HARNESS

a.

Connect the 4 connectors to the fan motors, hood courtesy switch and intake air temperature sensor.


b.

Attach the 13 clamps to the fan shroud.


Hide 16261G 18.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose clamp bracket to the upper radiator support with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Attach the hose clamp to the upper radiator support.


c.

Connect the No. 1 water by-pass hose to the radiator reservoir assembly and radiator hose sub-assembly, and slide the 2 clamps to secure the hose.


Hide 16533B 19.INSTALL NO. 1 RADIATOR SUPPORT

a.

Install the 2 radiator support cushions.


b.

Install the 2 No. 1 radiator supports with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 25770 20.CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

a.

Connect the No. 2 vacuum transmitting hose assembly, and slide the clip secure the hose.


Hide 16697A 21.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE LH

a.

Install the rear radiator side air guide plate LH with the 2 clips.


Hide 16695A 22.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH

a.

Install the front radiator side air guide plate LH and attach the 3 claws.


Hide 16693A 23.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE RH

a.

Install the rear radiator side air guide plate RH with the 2 clips.


Hide 16691A 24.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH

a.

Install the front radiator side air guide plate RH and attach the 3 claws.


Hide 88706 25.CONNECT LIQUID TUBE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the liquid tube sub-assembly and connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Connect the liquid tube sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88703 26.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the discharge hose sub-assembly and connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52131A 27.INSTALL FRONT BUMPER REINFORCEMENT

Hide 88625P 28.CONNECT AMBIENT TEMPERATURE SENSOR ASSEMBLY

a.

Attach the clamp to connect the ambient thermistor assembly.


Hide 16683A 29.INSTALL LOWER RADIATOR AIR GUIDE PLATE

a.

Install the lower radiator guide plate and attach the 3 claws.


Hide 16681A 30.INSTALL UPPER RADIATOR AIR GUIDE PLATE

a.

Install the upper radiator air guide plate with 6 clips.


Hide 52029 31.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly with the 2 bolts.

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



Hide 52085 32.INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY

a.

Install the front bumper center stay sub-assembly with the 2 bolts and clip.

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



Hide 86520 33.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 86510 34.INSTALL HIGH PITCHED HORN ASSEMBLY

Hide 74414B 35.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74411B 36.INSTALL FRONT BATTERY BRACKET

Hide 74431 37.INSTALL BATTERY TRAY

Hide 28800 38.INSTALL BATTERY

Hide 28899 39.INSTALL BATTERY INSULATOR

Hide 74404A 40.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 52618 41.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Install the front lower bumper absorber with the 4 screws.


Hide 52119A 43.INSTALL FRONT BUMPER COVER

Hide 44.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51441 52.INSTALL NO. 1 ENGINE UNDER COVER