Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions is met (2 trip detection logic):
·

2 or more of the P, N, NSW, R and D shift lever position signals are on simultaneously for 2 seconds.

·

The P, N, NSW, R and D shift lever position signals are all off simultaneously for 60 seconds.

·

The P, N, NSW or R shift lever position signal is on when the shift lever is in M for 2 seconds.


·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch assembly

·

Transmission control switch (shift lock control unit assembly)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0705 Ignition switch ON for 60 seconds

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position (P, R, N, D or M) and sends a signal to the ECM.

For safety, the engine can only be started when the park/neutral position switch detects that the shift lever is in P or N.

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously, or receives no position signal at all.

WIRING DIAGRAM

C200876
5.813,6.406 6.198,6.604 0.385,0.198 10 false ECM 4.313,1.885 5.146,2.083 0.833,0.198 10 false to ST Relay 0.396,1.802 1.844,2.167 1.448,0.365 10 false from Certification ECU (STAR) 5.26,5.75 5.573,5.948 0.313,0.198 10 false A61 5.583,5.719 5.896,5.917 0.313,0.198 10 false S 5.354,5.542 5.51,5.74 0.156,0.198 10 false 9 5.271,4.177 5.583,4.375 0.313,0.198 10 false B76 5.583,4.125 5.896,4.323 0.313,0.198 10 false P 5.323,3.99 5.542,4.188 0.219,0.198 10 false 53 5.26,3.573 5.573,3.771 0.313,0.198 10 false B76 5.583,3.521 5.896,3.719 0.313,0.198 10 false R 5.323,3.396 5.542,3.594 0.219,0.198 10 false 71 5.25,2.979 5.563,3.177 0.313,0.198 10 false B76 5.583,2.927 5.896,3.125 0.313,0.198 10 false N 5.323,2.792 5.542,2.99 0.219,0.198 10 false 70 5.25,2.385 5.563,2.583 0.313,0.198 10 false B76 5.583,2.323 5.896,2.521 0.313,0.198 10 false D 5.323,2.188 5.542,2.385 0.219,0.198 10 false 73 5.26,1.208 5.573,1.406 0.313,0.198 10 false B76 5.583,1.146 6,1.344 0.417,0.198 10 false NSW 5.323,1.021 5.542,1.219 0.219,0.198 10 false 38 3.771,2.01 3.99,2.208 0.219,0.198 10 false 9 3.771,2.458 3.99,2.656 0.219,0.198 10 false 7 3.771,3.063 3.99,3.26 0.219,0.198 10 false 8 3.771,4.26 3.99,4.458 0.219,0.198 10 false 3 3.771,3.656 3.99,3.854 0.219,0.198 10 false 2 3.771,5.854 3.99,6.052 0.219,0.198 10 false 5 3.604,1.75 3.823,1.948 0.219,0.198 10 false L 3.5,2.188 3.771,2.385 0.271,0.198 10 false DL 3.5,2.792 3.771,2.99 0.271,0.198 10 false NL 2.771,3.104 3.042,3.302 0.271,0.198 10 false RB 3.5,3.396 3.771,3.594 0.271,0.198 10 false RL 3.5,3.99 3.771,4.188 0.271,0.198 10 false PL 3.594,5.583 3.865,5.781 0.271,0.198 10 false S 2.771,1.75 2.99,1.948 0.219,0.198 10 false B 2.771,5.583 3.042,5.781 0.271,0.198 10 false IG 2.604,2.01 2.823,2.208 0.219,0.198 10 false 4 2.625,3.365 2.844,3.563 0.219,0.198 10 false 1 2.604,5.844 2.875,6.042 0.271,0.198 10 false 4 2.063,2.469 2.344,2.667 0.281,0.198 10 false *2 2.063,1.792 2.344,1.99 0.281,0.198 10 false *1 2.292,6.229 2.604,6.427 0.313,0.198 10 false G36 2.292,6.417 4.146,6.615 1.854,0.198 10 false Transmission Control Switch 0.219,5.75 1.99,6.125 1.771,0.375 10 false from ECU-IG NO. 1 Fuse 0.073,6.979 2.031,7.177 1.958,0.198 10 false *1: w/ Entry and Start System 0.073,7.354 2.115,7.552 2.042,0.198 10 false *2: w/o Entry and Start System 0.531,3.24 1.854,3.438 1.323,0.198 10 false from GAUGE Fuse 0.156,2.563 1.875,2.76 1.719,0.198 10 false from Ignition Switch (ST2) 2.313,4.635 2.625,4.833 0.313,0.198 10 false B36 2.313,4.823 4.146,5.021 1.833,0.198 10 false Park/Neutral Position Switch

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List.

Powertrain > Engine > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Shift Up SW
Sports Shift Down SW
Sports Mode Selection SW
Shift SW Status (D Range)
50003 61 190,377,150,378,158,157,155,151

g.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


Shift SW Status (R Range) PNP switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


Shift SW Status (N Range) PNP switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

ON: Shift lever in D

·

OFF: Shift lever not in D


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
C197711
0.292,0.885 0.729,1.146 0.438,0.26 1.604,1.01 1.073,0.292 false 2.115,1.021 2.563,0.271 false 0.354,0.927 0.729,1.156 0.375,0.229 10 false B36 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.958,0.094 1.271,0.292 0.313,0.198 10 false RB 2.552,0.083 2.865,0.281 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B36-1 (RB) - Body ground Always 11 to 14 V
B36-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
C197711
0.292,0.885 0.729,1.146 0.438,0.26 2.083,1.01 2.417,0.333 false 0.354,0.927 0.729,1.156 0.375,0.229 10 B36 0.052,0.042 0.365,0.24 0.313,0.198 10 *a 2.479,0.229 2.792,0.427 0.313,0.198 10 B
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B36-4 (B) - Body ground Ignition switch ON 11 to 14 V
B36-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

NG

8.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a.
C251979
0.552,1 0.969,1.302 0.417,0.302 2.229,1.594 1.865,1.281 false 0.104,0.083 0.417,0.24 0.313,0.156 10 *a 0.625,1.063 1.083,1.26 0.458,0.198 10 G36 2.26,1.635 2.573,1.833 0.313,0.198 10 IG
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.INSPECT TRANSMISSION CONTROL SWITCH
a.
C251980
1.542,1.271 1.896,1.656 false 1.052,1.635 1.292,1.281 false 0.104,0.125 0.417,0.281 0.313,0.156 10 *a 1.865,1.688 2.177,1.885 0.313,0.198 10 IG 0.927,1.667 1.24,1.865 0.313,0.198 10 S
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

7.REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
6.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.
C200874
1.51,2.438 1.948,2.698 0.438,0.26 1.51,0.323 1.948,0.583 0.438,0.26 0.656,4.104 1.125,3.26 false 1.156,4.313 1.125,3.458 false 1.625,4.125 1.198,3.458 false 2.26,4.292 1.344,3.448 false 2.333,2 2.146,1.01 false 1.583,2.49 1.958,2.719 0.375,0.229 10 B76 1.438,4.083 1.927,4.281 0.49,0.198 10 71 (R) 1.583,0.354 1.958,0.583 0.375,0.229 10 A61 0.052,0.031 0.333,0.229 0.281,0.198 10 *a 0.427,4.083 0.885,4.281 0.458,0.198 10 53 (P) 2.052,4.292 2.51,4.49 0.458,0.198 10 73 (D) 0.927,4.313 1.385,4.51 0.458,0.198 10 70 (N) 2.146,1.979 2.5,2.177 0.354,0.198 10 9 (S)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B76-53 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
B76-71 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
B76-70 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
B76-73 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
A61-9 (S) - Body ground
·

Ignition switch ON

·

Shift lever in M, "+" or "-"


11 to 14 V
B76-53 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
B76-71 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
B76-70 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
B76-73 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
A61-9 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in M, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.

Replace the lower shift lever assembly (transmission control switch).

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
C198257
0.313,1.115 0.75,1.375 0.438,0.26 1.5,2.427 1.938,2.688 0.438,0.26 2.115,1.167 2.479,0.49 false 1.823,4.052 1.698,3.167 false 0.375,1.156 0.75,1.385 0.375,0.229 10 B36 2.552,0.375 2.865,0.573 0.313,0.198 10 B 0.052,0 0.365,0.198 0.313,0.198 10 *a 1.552,2.479 1.927,2.708 0.375,0.229 10 B76 0.073,2.271 0.385,2.469 0.313,0.198 10 *b 1.51,4.063 2.219,4.26 0.708,0.198 10 38 (NSW)
*a Front view of wire harness connector
(to Park/Neutral Position Switch)
*b Front view of wire harness connector
(to ECM)


Disconnect the park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-4 (B) - B76-38 (NSW) Always Below 1 Ω
B36-4 (B) or B76-38 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON for 60 seconds.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END