Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049517 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67001A 1.INSTALL FRONT DOOR PANEL CUSHION

a.

Install 2 new front door panel cushions.


Hide 75074 2.INSTALL FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 75792 4.INSTALL DOOR WINDOW FRAME MOULDING CLIP

Hide 75756C 5.INSTALL FRONT DOOR WINDOW REAR FRAME MOULDING LH

Hide 67664C 6.INSTALL DOOR FRAME GARNISH LH

a.

Attach the clip to install a new door frame garnish LH.


Hide 67862 7.INSTALL FRONT DOOR WEATHERSTRIP LH

a.

Attach the 18 clips to install the front door weatherstrip LH.


b.

Attach the 2 clips.


Hide 68620 8.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door check assembly LH.


b.

When reusing a bolt labeled A:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.

Install the front door check assembly to the door panel with the 2 bolts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.
B337360C02
1.292,1.844 1.76,1.531 false 2.281,1.792 2.271,1.365 false 1.74,0.344 2.302,0.344 false 2.219,1.802 2.531,1.958 0.313,0.156 10 *1 2.323,0.26 2.635,0.417 0.313,0.156 10 *2 1.125,1.781 1.438,1.938 0.313,0.156 10 *2
*1 Bolt A
*2 Bolt B


Install the front door check assembly to the body panel with the bolt labeled A.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69312 9.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.

Install the front door lock open rod LH to the front door outside handle frame sub-assembly LH.


b.
B333940C01
2.646,0.365 2.896,0.271 false 3.01,0.521 3.344,0.719 0.333,0.198 10 (1) 2.427,0.094 2.76,0.292 0.333,0.198 10 (2) 2.927,0.167 3.156,0.354 0.229,0.188 10 *1
*1 Snap


Rotate the snap in the direction indicated by the arrow shown in the illustration to attach the snap to the front door lock open rod LH.


Hide 69202A 10.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle frame sub-assembly LH.


b.
B341307C01
0.042,0.052 0.354,0.208 0.313,0.156 10 *A 0.063,2.25 0.375,2.406 0.313,0.156 10 *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, attach the claw to install the front door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

w/ Entry and Start System:

Attach the 3 clamps.


Hide 69241H 11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 3 claws to install the front door front outside handle pad.


Hide 69242F 12.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door rear outside handle pad.


Hide 69220 13.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle assembly LH.


b.
B337364

Install the front door outside handle assembly LH by moving it in the direction indicated by the arrow shown in the illustration.


c.

w/ Entry and Start System:

i.

Attach the claw of the connector to connect the connector.


ii.

Attach the 2 claws of the connector cover to connect the connector cover.



Hide 69760C 14.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable assembly LH.


b.

Attach the 3 claws to close the cover.


Hide 69720B 15.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable assembly LH.


Hide 69040A 16.INSTALL FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 69052 17.INSTALL DOOR LOCK CYLINDER LH

a.

Attach the 2 claws to install the door lock cylinder LH to the front door outside handle cover LH.


Hide 69217F 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH

a.

Using a T30 "TORX" socket wrench, install the front door outside handle cover LH together with the front door lock cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 75720 19.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 67924 20.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

HINT:

When installing the front door No. 2 stiffener cushion, heat the front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door panel excessively.


a.

Clean the front door panel surface.

i.

Using a heat light, heat the front door panel surface.


ii.

Remove the double-sided tape from the front door panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door No. 2 stiffener cushion.

i.

Using a heat light, heat the front door panel.


ii.

Remove the peeling paper from the face of the front door No. 2 stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front door No. 2 stiffener cushion with the 2 bolts.

HINT:

Press the front door No. 2 stiffener cushion firmly to install it.


Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)



Hide 67404F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Attach the guide to install the front door rear lower frame sub-assembly LH with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 85720C 22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 23.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly LH.


b.

Temporarily install the temporary bolt to the front door window regulator sub-assembly LH.


c.
B341324C01
2.094,1.125 1.396,0.313 true 2.344,1.823 2.552,2.052 0.208,0.229 10 (1) 2.635,0.792 2.833,1.01 0.198,0.219 10 (2) 2.177,0.927 2.385,1.177 0.208,0.25 10 (3) 2.698,1.615 2.917,1.833 0.219,0.219 10 (4) 1.792,1.094 1.99,1.344 0.198,0.25 10 (5) 1.521,0.958 1.729,1.208 0.208,0.25 10 (6) 1.24,0.229 1.458,0.448 0.219,0.219 10 *1
*1 Temporary Bolt


Install the front door window regulator sub-assembly LH with the 5 bolts, and then tighten the temporary bolt.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the front door window regulator as it may become damaged.



d.

Connect the connector.


Hide 68151D 24.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run LH.


Hide 68102 25.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Operate the front door window regulator so that the front door glass can be installed.


d.

Disconnect the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the power window regulator master switch assembly with front door armrest base panel.


f.
B337363E01
1.906,0.281 2.229,0.51 0.323,0.229 10 (1) 0.552,0.625 1.115,0.844 0.563,0.219 10 (2)

Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.


g.

Install the front door glass sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67832 26.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel.


b.
B341312C01
0.438,0.354 0.292,0.396 false 2.573,0.531 2.656,0.573 false 0.76,3.677 1,3.896 0.24,0.219 10 *A 0.125,0.354 0.354,0.531 0.229,0.177 10 *a 2.688,0.531 2.896,0.76 0.208,0.229 10 *a
*A w/ Side Airbag Sensor
*a Reference Point


Pass the front door inside locking cable assembly LH, front door lock remote control cable assembly LH and wire harness through a new front door service hole cover LH, and then attach the front door service hole cover LH using the reference points on the front door panel.

HINT:
·

Securely install the front door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the front door service hole cover.

·

After installing the front door service hole cover, check the seal quality.




c.

Connect the connector.


d.

Attach the 3 clamps.


e.

w/ Side Airbag Sensor:

Install the bolt to the wire harness.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 86160 27.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/ Speaker)

Hide 86262E 28.INSTALL FRONT SPEAKER COVER (w/o Speaker)

a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new rivet into the nose piece.


c.

Insert the mandrel part of a new rivet into the nose piece.


d.

Using the riveter, install the front speaker cover with the 3 rivets as shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.

B337367


NOTICE:
·
B171664C06
1.229,1.104 1.083,1.635 1.083,1.635 1.24,2.198 false 1.083,1.635 0.813,1.635 false 1.75,0.885 2.031,1.635 2.031,1.635 1.771,2.51 false 2.031,1.625 2.313,1.625 false 0.667,1.563 0.979,1.719 0.313,0.156 10 *1 2.354,1.542 2.667,1.698 0.313,0.156 10 *2 2.417,0.604 2.729,0.76 0.313,0.156 10 *a 2.396,2.448 2.708,2.604 0.313,0.156 10 *b
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390C06
0.719,0.188 1.021,0.188 false 0.813,1.188 1.01,1.188 false 0.813,2.479 1.01,2.479 false 1.052,2.396 1.365,2.552 0.313,0.156 10 *1 2.479,1.563 2.792,1.719 0.313,0.156 10 *a 2.49,2.781 2.802,2.938 0.313,0.156 10 *b 1.063,1.115 1.375,1.271 0.313,0.156 10 *1 2.49,0.563 2.802,0.719 0.313,0.156 10 *a 1.052,0.104 1.365,0.26 0.313,0.156 10 *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the front speaker cover.

·

Do not tilt the riveter when installing the rivet to the front speaker cover.

·

Do not leave any space between the rivet head and front speaker cover.

·
B172391C06
0.74,0.677 0.938,0.677 false 0.729,2.146 0.938,2.146 false 0.969,2.063 1.281,2.219 0.313,0.156 10 *1 2.531,1.031 2.844,1.188 0.313,0.156 10 *a 2.552,2.479 2.865,2.635 0.313,0.156 10 *b 0.969,0.594 1.281,0.75 0.313,0.156 10 *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the front speaker cover and front door panel. Firmly hold together the 2 items while installing the rivet.




Hide 89835 29.INSTALL DOOR SIDE AIRBAG SENSOR LH

Hide 87940 30.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 68172A 31.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B337361

Install the front door inner glass weatherstrip LH to the front door trim board sub-assembly LH and fold down the 7 claws in the directions indicated by the arrows shown in the illustration.


Hide 69206B 32.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Attach the 2 claws and guide to install the front door inside handle sub-assembly LH.


Hide 67602 33.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


b.

Engage the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the 2 clamps.


c.

Attach the 9 clips to install the front door trim board sub-assembly LH.


d.

Install the 3 screws.


Hide 69284C 34.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.

Attach the 3 claws to install the front door inside handle bezel plug LH.


Hide 74642A 35.INSTALL FRONT DOOR ASSIST GRIP COVER LH

a.

Attach the guide, 2 clips and 4 claws to install the front door assist grip cover LH.


Hide 84820 36.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 37.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.

Attach the 6 claws, 2 guides and 2 clips to install the power window regulator master switch assembly with front door armrest base panel.


Hide 84810 38.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 39.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.

Attach the 6 claws, 2 guides and 2 clips to install the power window regulator switch assembly with front door armrest base panel.


Hide 67492A 40.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 2 claws, 2 clips and 2 guides to install the front door lower frame bracket garnish.


Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 43.INITIALIZE POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

Hide 45.CHECK POWER DOOR LOCK CONTROL SYSTEM