Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008788 SEAT BELT _0049193 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects the state of the front seat inner belt assembly RH*1 (or LH*2) when the front passenger seat is occupied with the ignition switch ON. If the front passenger side seat belt is not fastened, the front side seat belt warning light of the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.

*1: for LHD

*2: for RHD

HINT:

The front seat belt warning light on the combination meter assembly is used for both the driver side seat and front passenger side seat.


WIRING DIAGRAM

C279320E01
5.729,1.615 7.104,2.063 1.375,0.448 10 false Combination Meter Assembly 0.167,3.031 1.854,3.229 1.688,0.198 10 false *1: for LHD 0.135,3.302 1.823,3.5 1.688,0.198 10 false *2: for RHD 1.896,2.469 3.583,2.667 1.688,0.198 10 false M31*1 1.896,2.688 5.427,2.896 3.531,0.208 10 false Front Seat Inner Belt Assembly RH 1.906,3.146 3.594,3.344 1.688,0.198 10 false N35*2 1.896,3.333 5.427,3.542 3.531,0.208 10 false Front Seat Inner Belt Assembly LH 3.854,1.771 4.135,1.99 0.281,0.219 10 false 2 3.635,1.792 3.917,2.01 0.281,0.219 10 false E 2.813,2.021 3.854,2.26 1.042,0.24 10 false Buckle Switch 1.917,0.969 2.698,1.604 0.781,0.635 10 false Occupant Detection Sensor 0.281,1.021 1.719,1.802 1.438,0.781 10 false Separate Type Front Seat Cushion Pad 3.625,0.719 4.01,1.01 0.385,0.292 10 false + 3.854,0.698 4.24,0.99 0.385,0.292 10 false 3 5.729,1.417 6.115,1.708 0.385,0.292 10 false G16 5.802,0.698 5.979,0.948 0.177,0.25 10 false 7 5.979,0.823 6.49,1.094 0.51,0.271 10 false P/SB

PROCEDURE

1.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle switch signal ON/OFF ON: Front passenger side seat belt fastened
OFF: Front passenger side seat belt unfastened
Perform the inspection while sitting in the front passenger seat.
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the front passenger side seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY AND BODY GROUND)
a.

Disconnect the M31*1 or N35*2 front passenger seat inner belt assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G16 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
M31-3 (+) - G16-7 (P/SB) Always Below 1 Ω
M31-2 (E) - Body ground
M31-3 (+) - Body ground 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
N35-3 (+) - G16-7 (P/SB) Always Below 1 Ω
N35-2 (E) - Body ground
N35-3 (+) - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE FRONT SEAT INNER BELT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FRONT SEAT INNER BELT ASSEMBLY
a.

Temporarily replace the front seat inner belt assembly RH*1 or LH*2 with a new or normally functioning one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

*1: for LHD

*2: for RHD



Result:
Proceed to
NEXT



NEXT

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD
4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD
a.

Remove the separate type front seat cushion pad.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Inspect the separate type front seat cushion pad.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD