| Detection Item | Symptom | Trouble Area |
|---|---|---|
| ECM Communication Stop Mode | Either condition is met:
|
·
Power source or inside ECM ·
ECM CAN main wire or connector ·
ECM |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
DTC check procedure: Drive the vehicle for 50 seconds at a speed of 20 km/h (12 mph).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
| *A | for 2AR-FE, 3ZR-FAE, 3ZR-FE |
| *B | for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF |
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Connector | Specified Condition |
|---|---|---|
| A62-13 (CANH) - A62-26 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-7 (CANH) - A61-6 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
for 2AR-FE:
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-1 (BATT) - Body ground | Always | 11 to 14 V |
| A62-2 (+B) - Body ground | Battery positive (+) voltage applied to terminal A62-46 (MREL) | 11 to 14 V |
| A62-3 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A62-46 (MREL) | 11 to 14 V |
| A62-37 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B77-16 (E1) - Body ground | Always | Below 1 Ω |
| B77-49 (E02) - Body ground | Always | Below 1 Ω |
| B77-50 (E01) - Body ground | Always | Below 1 Ω |
| B77-58 (ME01) - Body ground | Always | Below 1 Ω |
for 3ZR-FAE, 3ZR-FE:
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-1 (BATT) - Body ground | Always | 11 to 14 V |
| A62-2 (+B) - Body ground | Battery positive (+) voltage applied to terminal A62-46 (MREL) | 11 to 14 V |
| A62-3 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A62-46 (MREL) | 11 to 14 V |
| A62-37 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B75-16 (E1) - Body ground | Always | Below 1 Ω |
| B75-21 (E02) - Body ground | Always | Below 1 Ω |
| B75-51 (E01) - Body ground | Always | Below 1 Ω |
| B75-59 (ME01) - Body ground | Always | Below 1 Ω |
for 1AD-FTV, 2AD-FHV, 2AD-DPF, 2AD-CCO:
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-2 (BATT) - Body ground | Always | 11 to 14 V |
| A61-1 (+B) - Body ground | Battery positive (+) voltage applied to terminal A61-45 (MREL) | 11 to 14 V |
| A61-20 (+B2) - Body ground | Battery positive (+) voltage applied to terminal A61-45 (MREL) | 11 to 14 V |
| A61-25 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B76-44 (E02) - Body ground | Always | Below 1 Ω |
| B76-45 (E01) - Body ground | Always | Below 1 Ω |
| B76-84 (ME01) - Body ground | Always | Below 1 Ω |
| B76-109 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 1AD-FTV: Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-CCo, 2AD-DPF: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
NG