Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1500 Fuel Sender Open Detected Both conditions are met:
·

IG voltage is 10.5 V or higher.

·

Average input signal of fuel sender gauge is 550 Ω or more 3 times consecutively


·

Fuel sender gauge assembly

·

Harness or connector

·

Combination meter assembly



WIRING DIAGRAM

E270440E01
4.313,4.177 6.385,4.521 2.073,0.344 10 Combination Meter Assembly 4.292,3.979 4.74,4.208 0.448,0.229 10 G16 5.083,1.875 5.531,2.104 0.448,0.229 10 CPU 5.531,1.385 5.979,1.615 0.448,0.229 10 FUEL 4.583,1.063 5.031,1.292 0.448,0.229 10 I/F 1.677,2.125 2.125,2.354 0.448,0.229 10 V2 1.688,2.313 3.667,2.573 1.979,0.26 10 Fuel Sender Gauge Assembly 1.896,1.573 2.052,1.76 0.156,0.188 10 1 3.063,1.563 3.271,1.729 0.208,0.167 10 2 4,1 4.271,1.167 0.271,0.167 10 16 4.01,1.573 4.281,1.74 0.271,0.167 10 15 4.281,1 4.531,1.219 0.25,0.219 10 L 4.292,1.677 4.542,1.896 0.25,0.219 10 E

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal Min.: 0 l, Max.: 127.5 l Current fuel level displayed -
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39
OK:

Fuel amount value displayed on the GTS is almost the same as the needle indication.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the V2 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-16 (L) - V2-1 Always Below 1 Ω
G16-15 (E) - V2-2
G16-16 (L) or V2-1 - Body ground Always 10 kΩ or higher
G16-15 (E) or V2-2 - Body ground



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

REPLACE COMBINATION METER ASSEMBLY

NG (1AD-FTV)

REPLACE FUEL SENDER GAUGE ASSEMBLY

NG (2AD-FHV)

REPLACE FUEL SENDER GAUGE ASSEMBLY

NG (2AD-FTV)

REPLACE FUEL SENDER GAUGE ASSEMBLY

NG (2AR-FE)

REPLACE FUEL SENDER GAUGE ASSEMBLY

NG (3ZR-FAE)

REPLACE FUEL SENDER GAUGE ASSEMBLY

NG (3ZR-FE)

REPLACE FUEL SENDER GAUGE ASSEMBLY