Home › Drivetrain › EB61 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY
RM3090E _52 Drivetrain _008757 EB61 MANUAL TRANSMISSION / TRANSAXLE _0050275 MANUAL TRANSAXLE ASSEMBLY A

EB61 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 33403K 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with gear oil.


b.

Install the O-ring to the speedometer driven hole cover sub-assembly.


c.

Install the speedometer driven hole cover sub-assembly to the manual transaxle case with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 31400 2.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 3.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31407B 5.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31490 6.INSTALL CLUTCH ACCUMULATOR ASSEMBLY

Hide 12321A 7.INSTALL REAR ENGINE MOUNTING BRACKET

C279720C01
1.063,1.073 1.219,1.271 0.156,0.198 10 4 2.125,0.042 2.802,0.271 0.677,0.229 10 1 (*a), 5 2.573,0.563 2.729,0.76 0.156,0.198 10 3 2.385,1.635 2.542,1.833 0.156,0.198 10 2
*a Temporarily


a.

Temporarily install the rear engine mounting bracket with the 4 bolts.


b.

Tighten the 4 bolts of the rear engine mounting bracket in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

HINT:

As shown in the illustration, tighten the 4 bolts in order.



Hide 12325A 8.INSTALL ENGINE MOUNTING BRACKET LH

a.

Clean the bolts and the installation holes in the engine mounting bracket LH.


b.
C279718C01
1.052,0.615 1.208,0.813 0.156,0.198 10 4 0.99,1.427 1.146,1.625 0.156,0.198 10 2 2.177,0.677 3.052,0.906 0.875,0.229 10 1 (*a), 5 2.49,1.427 2.646,1.625 0.156,0.198 10 3
*a Temporarily


Apply adhesive to the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Temporarily install the engine mounting bracket LH with the 4 bolts.


d.

Tighten the 4 bolts of the engine mounting bracket LH in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12311A 9.INSTALL FRONT ENGINE MOUNTING BRACKET

C279719C01
0.281,0.073 1,0.271 0.719,0.198 10 1 (*a), 5 1.708,0.115 1.865,0.313 0.156,0.198 10 3 1.094,1.771 1.25,1.969 0.156,0.198 10 2 1.813,0.875 1.969,1.073 0.156,0.198 10 4
*a Temporarily


a.

Temporarily install the front engine mounting bracket with the 4 bolts.


b.

Tighten the 4 bolts of the front engine mounting bracket in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 30300 10.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.

Align the input shaft with the clutch disc and install the manual transaxle to the engine.

NOTICE:
·

Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.

·

Insert the dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts.




b.
C277967C01
2.323,0.042 3.271,0.302 0.948,0.26 10 A: 1(*a), 4 2.552,0.313 3.167,0.51 0.615,0.198 10 A: 3 2.49,1.896 2.646,2.094 0.156,0.198 10 B 2.073,1.979 2.229,2.177 0.156,0.198 10 B 1.146,1.917 1.302,2.115 0.156,0.198 10 B 0.917,1.625 1.073,1.823 0.156,0.198 10 B 0.771,0.688 0.927,0.885 0.156,0.198 10 B 0.844,0.104 1.365,0.333 0.521,0.229 10 A: 2
*a Temporarily


Temporarily install the manual transaxle assembly with the bolt(*a).


c.

Tighten the 3 bolts labeled A in the order shown in the illustration, and then install the 5 bolts labeled B.

Torque:
for Bolt A : 38 N*m (387 kgf*cm, 28 ft.*lbf)
for Bolt B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Connect the back-up light switch connector and install the engine wire to the manual transaxle assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.

Connect the clamp with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE