Home › Drivetrain › CLUTCH › CLUTCH ACCUMULATOR(for Gasoline) › 2012.12–2013.11
RM3090E _52 Drivetrain _008754 CLUTCH _0050761 CLUTCH ACCUMULATOR(for Gasoline) A

CLUTCH  CLUTCH ACCUMULATOR(for Gasoline)  INSTALLATION  


PROCEDURE

Hide 31490 1.INSTALL CLUTCH ACCUMULATOR ASSEMBLY

a.

Install the clutch accumulator assembly.

i.

for 2AR-FE:

Temporarily install the clutch accumulator assembly to the manual transaxle assembly with the 3 bolts.


ii.

for 3ZR-ZE, 3ZR-FAE:

Temporarily install the clutch accumulator assembly and engine wire to the manual transaxle assembly with the 3 bolts.



b.
C279755C02
2.26,2.5 2.385,2.323 2.385,2.323 2.604,2.323 false 1.333,3.927 1.51,4.156 0.177,0.229 10 false 1 1.344,3.063 1.521,3.292 0.177,0.229 10 false 2 2.76,3.042 2.938,3.271 0.177,0.229 10 false 3 1.354,1.396 1.531,1.625 0.177,0.229 10 false 1 1.344,0.51 1.521,0.74 0.177,0.229 10 false 2 2.792,0.5 2.969,0.729 0.177,0.229 10 false 3 2.698,2.24 2.948,2.469 0.25,0.229 10 false *1 0.104,2.292 0.354,2.552 0.25,0.26 10 false *B 0.052,0.052 0.281,0.281 0.229,0.229 10 false *A
*A for 2AR-FE
*B for 3ZR-FE, 3ZR-FAE
*1 Engine Wire


Tighten the 3 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.
C280409C01
2.229,0.208 1.979,0.208 1.979,0.208 1.729,0.427 true 0.406,1.635 0.563,1.833 0.156,0.198 10 A 2.292,0.135 2.51,0.385 0.219,0.25 10 *a 2.635,2.042 2.792,2.24 0.156,0.198 10 A 2.635,2.469 2.792,2.667 0.156,0.198 10 B
*a Paint Mark


Temporarily install the bleeder to accumulator tube labeled A and accumulator to flexible hose tube labeled B.


d.

Install the clamp with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:

Align the clamp and paint mark as shown in the illustration and install the clamp.



e.

Using a 10 mm union nut wrench, tighten the bleeder to accumulator tube labeled A and accumulator to flexible hose tube labeled B.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



f.

Connect the accumulator to flexible hose tube and clutch hose.


g.
C277990N01
2.688,1.823 2.844,2.021 0.156,0.198 10 A 1.771,1.948 1.927,2.146 0.156,0.198 10 B

Install the clutch hose with a new clip labeled A.


h.

Using a 10 mm union nut wrench, tighten the accumulator to flexible hose tube labeled B.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 4.INSPECT FOR FLUID LEAK

HINT:

Check for leaks in the clutch system.


Hide 51444C 6.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 7.INSTALL NO. 1 ENGINE UNDER COVER (for 2AR-FE, 3ZR-FE)

Hide 51441 8.INSTALL NO.1 ENGINE UNDER COVER (for 3ZR-FAE)