Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0050250 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system. Even if there is a malfunction in the stop light signal circuit while the cruise control is in operation, normal driving is maintained due to a fail-safe function.

Cruise control is canceled when positive voltage is applied to terminal STP.

When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels the cruise control.

When the brake pedal is released, positive voltage is applied to terminal ST1- of the ECM through the IGN fuse and the stop light switch assembly, and the ECM operates the cruise control.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

ECM

·

Harness or connector



WIRING DIAGRAM

E270488E01
3.125,1.677 3.438,1.875 0.313,0.198 10 A5 3.115,1.854 4.229,2.26 1.115,0.406 10 Stop Light Switch Assembly 5.885,1.885 6.344,2.083 0.458,0.198 10 ECM 5.698,1.344 6.156,1.542 0.458,0.198 10 STP 5.688,0.563 6.302,0.76 0.615,0.198 10 ST1- 2.167,1.479 2.781,1.677 0.615,0.198 10 STOP 2.229,0.688 2.688,0.885 0.458,0.198 10 IGN 0.375,1.344 2.208,1.542 1.833,0.198 10 from Battery 4.615,0.781 4.927,0.979 0.313,0.198 10 *1 4.979,0.781 5.292,0.979 0.313,0.198 10 *2 5.344,0.781 5.656,0.979 0.313,0.198 10 *3 4.594,1.573 4.906,1.771 0.313,0.198 10 *1 4.969,1.563 5.281,1.76 0.313,0.198 10 *2 5.333,1.573 5.646,1.771 0.313,0.198 10 *3 0.063,1.781 3.531,1.979 3.469,0.198 10 *1: for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF 0.073,2.094 2.219,2.292 2.146,0.198 10 *2: for 2AR-FE 0.073,2.406 2.219,2.604 2.146,0.198 10 *3: for 3ZR-FAE, 3ZR-FE 0.229,0.542 2.063,0.74 1.833,0.198 10 from IG2 Relay 3.958,0.427 4.271,0.625 0.313,0.198 10 3 3.063,0.438 3.375,0.635 0.313,0.198 10 4 3.958,1.229 4.271,1.427 0.313,0.198 10 1 3.063,1.229 3.375,1.427 0.313,0.198 10 2 4.573,0.552 5.031,0.75 0.458,0.198 10 A61 4.573,1.354 5.031,1.552 0.458,0.198 10 A61 4.938,0.552 5.396,0.75 0.458,0.198 10 A62 4.938,1.354 5.396,1.552 0.458,0.198 10 A62 5.323,0.552 5.781,0.75 0.458,0.198 10 A62 5.313,1.354 5.771,1.552 0.458,0.198 10 A62 5.344,0.313 5.802,0.51 0.458,0.198 10 10 5.396,1.135 5.854,1.333 0.458,0.198 10 9 4.99,0.313 5.448,0.51 0.458,0.198 10 24 4.969,1.125 5.427,1.323 0.458,0.198 10 11 4.594,0.313 5.052,0.51 0.458,0.198 10 34 4.625,1.125 5.083,1.323 0.458,0.198 10 35

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
E270489C01
1.521,0.156 1.906,0.427 0.385,0.271 0.083,0.083 0.396,0.281 0.313,0.198 10 *a 1.615,0.208 1.927,0.406 0.313,0.198 10 A5
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-2 - Body ground Always 11 to 14 V
A5-4 - Body ground Ignition switch ON 11 to 14 V
A5-4 - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF

i.

Disconnect the A61 ECM connector.


ii.

Disconnect the A5 stop light switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-34 (ST1-) - A5-3 Always Below 1 Ω
A61-35 (STP) - A5-1 Always Below 1 Ω
A61-34 (ST1-) or A5-3 - Body ground Always 10 kΩ or higher
A61-35 (STP) or A5-1 - Body ground Always 10 kΩ or higher




b.

for 2AR-FE

i.

Disconnect the A62 ECM connector.


ii.

Disconnect the A5 stop light switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-1 (STP) - A5-1 Always Below 1 Ω
A62-24 (ST1-) - A5-3 Always Below 1 Ω
A62-1 (STP) or A5-1 - Body ground Always 10 kΩ or higher
A62-24 (ST1-) or A5-3 - Body ground Always 10 kΩ or higher




c.

for 3AR-FAE, 3ZR-FE

i.

Disconnect the A62 ECM connector.


ii.

Disconnect the A5 stop light switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-9 (STP) - A5-1 Always Below 1 Ω
A62-10 (ST1-) - A5-3 Always Below 1 Ω
A62-9 (STP) or A5-1 - Body ground Always 10 kΩ or higher
A62-10 (ST1-) or A5-3 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR