When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.
If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.
If the transponder key ECU assembly or key is replaced, refer to the Service Bulletin.
When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Proceed to |
|---|
| DTCs are not output (for Gasoline) |
| DTCs are not output (for Diesel) |
| DTCs are output |
DTCs are not output (for Gasoline)
DTCs are not output (for Diesel)
DTCs are output
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | OFF/ON | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
OFF is displayed after the engine is started.
| Proceed to |
|---|
| OK (for 2AR-FE) |
| OK (for 3ZR-FAE) |
| OK (for 3ZR-FE) |
| NG |
OK (for 2AR-FE)
OK (for 3ZR-FAE)
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
OK (for 3ZR-FE)
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.
Security indicator light turns off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.
Security indicator light turns off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using another registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| Engine can be started |
| Engine cannot be started |
Engine can be started
Engine cannot be started
Replace the transponder key coil.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| Engine can be started |
| Engine cannot be started |
Engine can be started
Engine cannot be started
Replace the transponder key ECU assembly with a new one.
Refer to the Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| Engine can be started |
| Engine cannot be started |
Engine can be started
Engine cannot be started
Replace the key.
Key ID code registration is necessary when replacing the key.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| Engine can be started |
| Engine cannot be started (for 2AR-FE) |
| Engine cannot be started (for 3ZR-FAE) |
| Engine cannot be started (for 3ZR-FE) |
| Engine cannot be started (for 1AD-FTV) |
| Engine cannot be started (for 2AD-CCo) |
| Engine cannot be started (for 2AD-DPF) |
| Engine cannot be started (for 2AD-FHV) |
Engine can be started
Engine cannot be started (for 2AR-FE)
Engine cannot be started (for 3ZR-FAE)
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Engine cannot be started (for 3ZR-FE)
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Engine cannot be started (for 1AD-FTV)
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Engine cannot be started (for 2AD-CCo)
Engine cannot be started (for 2AD-DPF)
Engine cannot be started (for 2AD-FHV)
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING