Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0050250 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

E270491E02
6.292,2.375 6.75,2.573 0.458,0.198 10 false ECM 4.417,1.135 4.729,1.333 0.313,0.198 10 false A1 2.396,1.135 2.708,1.333 0.313,0.198 10 false A1 2.76,1.135 3.073,1.333 0.313,0.198 10 false F1 4.052,1.135 4.365,1.333 0.313,0.198 10 false F1 2.792,1.594 6.156,1.792 3.365,0.198 10 false Clutch Switch Assembly 0.094,2.552 1.781,2.75 1.688,0.198 10 false *1: for LHD 0.104,2.927 1.792,3.125 1.688,0.198 10 false *2: for RHD 0.104,3.313 4.396,3.51 4.292,0.198 10 false *3: for 1AD-FTV, 2AD-CCo, 2AD-DPF 2.396,1.375 2.708,1.573 0.313,0.198 10 false *1 4.417,1.365 4.729,1.563 0.313,0.198 10 false *1 2.781,1.385 3.094,1.583 0.313,0.198 10 false *2 4.073,1.365 4.385,1.563 0.313,0.198 10 false *2 5,1.135 5.458,1.333 0.458,0.198 10 false B76 5.365,1.135 5.823,1.333 0.458,0.198 10 false B77 5.729,1.135 6.188,1.333 0.458,0.198 10 false B75 5.042,1.365 5.354,1.563 0.313,0.198 10 false *3 5.417,1.375 5.729,1.573 0.313,0.198 10 false *4 5.771,1.365 6.083,1.563 0.313,0.198 10 false *5 6.094,1.135 6.25,1.333 0.156,0.198 10 false D 1.302,1.323 2.677,1.521 1.375,0.198 10 false EFI NO. 1*3 5.417,0.917 5.729,1.115 0.313,0.198 10 false 67 5.771,0.927 6.083,1.125 0.313,0.198 10 false 81 5.031,0.917 5.344,1.115 0.313,0.198 10 false 73 4.458,0.927 4.771,1.125 0.313,0.198 10 false 2 4.083,0.917 4.396,1.115 0.313,0.198 10 false 2 2.802,0.927 3.115,1.125 0.313,0.198 10 false 1 2.448,0.917 2.76,1.115 0.313,0.198 10 false 1 1.427,0.052 6.021,0.271 4.594,0.219 10 false from EFI-MAIN NO. 2 Relay*3 2.802,2.531 6.469,2.729 3.667,0.198 10 false *4: for 2AR-FE 2.823,2.917 6.49,3.115 3.667,0.198 10 false *5: for 3ZR-FAE, 3ZR-FAE 1.063,1.667 2.521,1.875 1.458,0.208 10 false ECU-IG NO. 3*4, *5 1.427,0.438 6.021,0.656 4.594,0.219 10 false from IG1 NO. 2 Relay*4, *5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM AND BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM AND BATTERY)
a.

for 1AD-FTV, 2AD-CCo, 2AD-DPF

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B76 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B76-73 (D) Always Below 1 Ω
A1-2 or B76-73 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B76-73 (D) Always Below 1 Ω
F1-2 or B76-73 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




b.

for 2AR-FE

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B77 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B77-67 (D) Always Below 1 Ω
A1-2 or B77-67 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B77-67 (D) Always Below 1 Ω
F1-2 or B77-67 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




c.

for 3ZR-FAE, 3ZR-FE

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B75 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B75-81 (D) Always Below 1 Ω
A1-2 or B75-81 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B75-81 (D) Always Below 1 Ω
F1-2 or B75-81 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR