Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P06DB  Engine Oil Pressure Control Circuit Low  P06DC  Engine Oil Pressure Control Circuit High  


DESCRIPTION

Refer to DTC P0524.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0524

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P06DB Engine Oil Pressure Control Circuit Low Open or short in the oil pressure switching valve circuit for 1 second (1 trip detection logic).
·

Open or short in oil pressure switching valve assembly circuit

·

Oil pressure switching valve assembly

·

ECM


Does not come on DTC stored
P06DC Engine Oil Pressure Control Circuit High Open or short in the oil pressure switching valve circuit for 1 second (1 trip detection logic).
·

Open or short in oil pressure switching valve assembly circuit

·

Oil pressure switching valve assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P06DB
P06DC
Eng Oil Press Switch Valve

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P06DB After warming up the engine, race the engine at 2200 rpm or higher.*
P06DC

*: Using the GTS, the oil pressure control system can be inspected by performing Engine Oil Pressure Control Check. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Inspect the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PRESSURE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SWITCHING VALVE ASSEMBLY)

NG

9.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SWITCHING VALVE ASSEMBLY)
a.
A154589
0.833,1.302 1.208,1.552 0.375,0.25 0.167,0.115 0.448,0.323 0.281,0.208 10 false *a 0.906,1.344 1.292,1.521 0.385,0.177 10 false B65
*a Front view of wire harness connector
(to Oil Pressure Switching Valve Assembly)


Disconnect the oil pressure switching valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B65-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - ECM)
a.

Disconnect the oil pressure switching valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B65-1 - B76-83 (EOPV) Always Below 1 Ω
B65-1 or B76-83 (EOPV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and warm it up.


g.

After warming up the engine, race the engine at 3000 rpm or higher.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

7.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SWITCHING VALVE ASSEMBLY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the oil pressure switching valve assembly connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B65-2 - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B65-2 or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK ECM POWER SOURCE CIRCUIT

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Replace the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PRESSURE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED