Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P0045  Turbocharger / Supercharger Boost Control Solenoid Circuit / Open  


DESCRIPTION

This DTC indicates that the vacuum regulating valve assembly of the turbocharger is malfunctioning. The ECM monitors the vacuum regulating valve assembly current to detect an open or short in the vacuum regulating valve assembly circuit. If the current is out of the standard range, the ECM stores a DTC and illuminates the MIL immediately.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0045 Turbocharger / Supercharger Boost Control Solenoid Circuit / Open Open or short in vacuum regulating valve assembly circuit for 0.5 seconds or more.
(1 trip detection logic)
·

Vacuum regulating valve assembly (for turbocharger control)

·

Open or short in vacuum regulating valve assembly (for turbocharger control) circuit

·

ECM


Comes on DTC stored

HINT:

If DTC P0045 is stored, the following symptoms may appear.


When the nozzle vane of the turbocharger is stuck closed:

- Vehicle surge when driving with full load

When the nozzle vane of the turbocharger is stuck open:

- Lack of power

- Vehicle surge or hesitation under light or medium load

- White smoke

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0045 Ignition switch ON for 1 second

WIRING DIAGRAM

A284163
3.167,1.333 5.49,2.021 2.323,0.688 10 false Vacuum Regulating Valve Assembly (for Turbocharger Control) 5.75,1.031 6.448,1.333 0.698,0.302 10 false VN 1.281,0.906 1.552,1.125 0.271,0.219 10 false 5 0.625,2.333 1.844,2.531 1.219,0.198 10 false EFI-MAIN NO. 2 1.219,1.719 2.438,1.917 1.219,0.198 10 false EFI-MAIN NO. 2 5.406,1.031 5.771,1.25 0.365,0.219 10 false B76 5.417,2.146 5.781,2.365 0.365,0.219 10 false A61 5.448,0.844 5.813,1.063 0.365,0.219 10 false 83 5.458,1.969 5.823,2.188 0.365,0.219 10 false 45 5.74,2.042 6.438,2.344 0.698,0.302 10 false MREL 2.604,0.844 3.385,1.031 0.781,0.188 10 false EFI NO. 1 1.281,1.417 1.552,1.635 0.271,0.219 10 false 2 2.115,1.417 2.385,1.635 0.271,0.219 10 false 1 2.125,0.927 2.396,1.146 0.271,0.219 10 false 3 4.719,0.896 4.99,1.115 0.271,0.219 10 false 2 3.719,0.896 3.99,1.115 0.271,0.219 10 false 1 0.604,3.021 1.823,3.219 1.219,0.198 10 false FL MAIN 3.219,1.177 3.813,1.448 0.594,0.271 10 false B43 6.167,3.875 6.76,4.146 0.594,0.271 10 false ECM 0.76,3.76 1.979,3.958 1.219,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
a.

Inspect the vacuum regulating valve assembly (for turbocharger control).

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

12.REPLACE VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
A204588
0.656,0.99 0.958,1.302 0.302,0.313 0.104,0.198 0.417,0.354 0.313,0.156 10 *a 0.688,1.094 1.146,1.292 0.458,0.198 10 B43
*a Front view of wire harness connector
(to Vacuum Regulating Valve Assembly (for Turbocharger Control))


Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B43-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - ECM)
a.

Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B43-2 - B76-83 (VN) Always Below 1 Ω
B43-2 or B76-83 (VN) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum regulating valve assembly (for turbocharger control) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL) - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B43-1 - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B43-1 or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 2 RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

10.REPLACE EFI-MAIN NO. 2 RELAY
7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE VACUUM REGULATING VALVE ASSEMBLY (FOR TURBOCHARGER CONTROL)
a.

Replace the vacuum regulating valve assembly (for turbocharger control).

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 1 second or more.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END