Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P011C  Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)  


DESCRIPTION

Refer to DTC P0112 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>P0112).

Refer to DTC P007C (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>P007C).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P011C Charge Air Temperature/Intake Air Temperature Correlation (Bank 1) After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (27°F) or higher.
(2 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Open or short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (built into mass air flow meter assembly)

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P011C
·

Intake Air

·

Intake Air Temp (Turbo)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P011C After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P011C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P011C is output
DTC P011C and other DTCs are output


HINT:

If any DTCs other than P011C are output, troubleshoot those DTCs first.




DTC P011C is output

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

DTC P011C and other DTCs are output

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 5°C (9°F).


NOTICE:

If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
3.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE (TURBO))

NG

8.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
4.READ VALUE USING GTS (INTAKE AIR TEMPERATURE (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

d.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 - B76-113 (THIA) Always Below 1 Ω
A54-1 - B76-90 (ETHI) Always Below 1 Ω
A54-2 or B76-113 (THIA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.REPAIR OR REPLACE HARNESS AND CONNECTOR
7.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-4 (THA) - B76-110 (THA) Always Below 1 Ω
B1-5 (E2) - B76-87 (ETHA) Always Below 1 Ω
B1-4 (THA) or B76-110 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE MASS AIR FLOW METER ASSEMBLY

NG

10.REPAIR OR REPLACE HARNESS AND CONNECTOR
9.REPLACE MASS AIR FLOW METER ASSEMBLY
a.

Replace the mass air flow meter assembly.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

NOTICE:

If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

g.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 15°C (27°F).



Result:
Proceed to
NEXT



NEXT

END