The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the EGR body.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0489 | Exhaust Gas Recirculation Control Circuit Low | The EGR actuator current is below 0.5 A for 2.0 seconds during EGR valve operation.
(1 trip detection logic) |
·
Open or short in EGR valve circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored |
| P0490 | Exhaust Gas Recirculation Control Circuit High | An EGR actuator current of 8 A or higher due to a mechanical malfunction, or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic) |
·
Open or short in EGR valve circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0489 | ·
Actual EGR Valve Pos. ·
Target EGR Position |
| P0490 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0489 | Idle the engine for 5 seconds or more |
| P0490 |
Refer to DTC P042E (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>P042E).
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).
Inspect the electric EGR valve assembly.
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>EGR VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i1-5 (M+) - B76-86 (EGM+) | Always | Below 1 Ω |
| i1-1 (M-) - B76-85 (EGM-) | Always | Below 1 Ω |
| i1-5 (M+) or B76-86 (EGM+) - Body ground | Always | 10 kΩ or higher |
| i1-1 (M-) or B76-85 (EGM-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 5 seconds or more
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT