Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E07
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A"
·

Conditions (a), (b), (c) and (d) are met for 8 seconds or more (2 trip detection logic):

(a) Engine coolant temperature is higher than 70°C (158°F).

(b) engine speed is 1500 to 4000 rpm

(c) Injection volume is 23 mm3/st or more.

(d) No speed signal is input to the ECM.

·

Conditions (a) and (b) are met for 6 seconds or more (2 trip detection logic):

(a) During the fuel-cut operation.

(b) No speed signal is input to the ECM.


·

Open or short in speedometer circuit

·

Speedometer assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0500 Vehicle Speed

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0500 Drive the vehicle at 10 km/h (6.3 mph) or more

WIRING DIAGRAM

A298514E02
2.156,2.177 4.76,2.375 2.604,0.198 10 false Combination Meter Assembly 2.156,2.01 2.698,2.219 0.542,0.208 10 false G16 5.302,2.021 5.844,2.229 0.542,0.208 10 false A61 5.844,2.021 6.385,2.229 0.542,0.208 10 false ECM 5.125,1.031 5.667,1.24 0.542,0.208 10 false SPD 4.885,1.073 5.427,1.281 0.542,0.208 10 false 14 3.833,1.073 4.375,1.271 0.542,0.198 10 false 6 5.896,0.771 6.438,0.979 0.542,0.208 10 false 5 V 3.521,1.073 4.063,1.271 0.542,0.198 10 false +S 2.333,1.083 2.875,1.281 0.542,0.198 10 false SI 2.125,1.083 2.667,1.281 0.542,0.198 10 false 5 0.125,1.198 1.552,1.719 1.427,0.521 10 false from Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

8.CHECK SPEEDOMETER CIRCUIT
2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CHECK TERMINAL VOLTAGE (+S VOLTAGE)
3.CHECK TERMINAL VOLTAGE (+S VOLTAGE)
a.
A127854C02
0.396,0.531 0.802,0.781 0.406,0.25 1.177,1.323 1.323,0.688 true 0.104,0.094 0.271,0.25 0.167,0.156 10 *a 0.469,0.573 0.781,0.729 0.313,0.156 10 G16 1.385,0.563 1.646,0.729 0.26,0.167 10 +S
*a Front view of wire harness connector
(to Combination Meter)


Disconnect the combination meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.

Turn the ignition switch to ON.


b.
A205820C02
0.156,0.792 0.563,1.052 0.406,0.26 2.104,1.115 2.781,2 true 0.115,0.156 0.344,0.385 0.229,0.229 10 *a 0.24,0.844 0.552,1.01 0.313,0.167 10 G16 2.604,2.042 3.229,2.229 0.625,0.188 10 6 (+S) 2.917,3.583 3.292,3.76 0.375,0.177 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Move the shift lever to neutral.


c.

Jack up the vehicle.


d.

Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


Result:
Proceed to
OK
NG




OK

7.REPLACE ECM

NG

5.REPLACE COMBINATION METER ASSEMBLY
5.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A61-14 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK SPEEDOMETER CIRCUIT
a.

Check the speedometer circuit.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Inspect the brake actuator assembly and speed sensor.



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off.


f.

Start the engine.


g.

Drive the vehicle at 10 km/h (6.3 mph) or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the pending DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END