Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal sensor assembly is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. The accelerator pedal sensor assembly has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal sensor assembly.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A255815
4.333,2.031 4.229,1.927 false 4.333,2.208 4.229,2.125 false 4.333,2.26 4.229,2.323 false 4.344,2.417 4.229,2.531 false 0.844,2.875 0.552,3.333 true 1.063,2.198 1.323,1.365 true 4.323,1.844 3.865,0.938 false 1.323,1.365 1.417,1.365 false 1.063,2.563 0.927,1.823 true 0.927,1.823 0.854,1.823 false 0.552,3.802 1.698,4.25 1.146,0.448 10 Accelerator Pedal Sensor Assembly 1.458,1.292 1.99,1.49 0.531,0.198 10 Magnet 0.313,1.74 0.844,1.917 0.531,0.177 10 IC No. 1 0.323,3.354 0.854,3.531 0.531,0.177 10 IC No. 2 2.188,1.74 2.531,1.917 0.344,0.177 10 VPA 2.188,2.063 2.542,2.25 0.354,0.188 10 EPA 2.104,2.385 2.542,2.583 0.438,0.198 10 VCPA 2.115,2.688 2.521,2.865 0.406,0.177 10 VPA2 2.115,3 2.51,3.177 0.396,0.177 10 EPA2 2.104,3.313 2.51,3.49 0.406,0.177 10 VCP2 2.677,3.76 3.063,3.938 0.385,0.177 10 ECM 4.271,1.531 4.469,1.708 0.198,0.177 10 *1 5.854,1.531 6.052,1.708 0.198,0.177 10 *2 3.938,1.833 4.229,2.01 0.292,0.177 10 4.55 3.854,2.042 4.219,2.219 0.365,0.177 10 3.988 3.938,2.25 4.229,2.427 0.292,0.177 10 3.75 3.854,2.458 4.219,2.635 0.365,0.177 10 3.188 4.042,2.823 4.292,3.031 0.25,0.208 10 1.6 4.031,3.052 4.271,3.229 0.24,0.177 10 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 0 5.781,3.594 6.073,3.771 0.292,0.177 10 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 Usable Range 4.667,3.896 6.563,4.167 1.896,0.271 10 Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 *2: Accelerator Pedal Fully Depressed 2.021,0.813 3.833,1.281 1.813,0.469 10 Accelerator Pedal Sensor Assembly Output Voltage (V) 6.479,2.281 6.802,2.458 0.323,0.177 10 VPA 6.427,1.823 6.833,2 0.406,0.177 10 VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V and VPA2 is more than 0.97 deg, or VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

VPA circuit open or ground short

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V
(b) VPA1 is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

VPA2 circuit open or ground short

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is higher than 4.8 V.
(b) VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) continues for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is below 0.02 V.
(b) VPA is below 0.4 V and VPA2 is below 1.2 V.
·

Accelerator pedal sensor assembly

·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal sensor assembly deformed

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2120
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %


P2122
P2123
P2125
P2127
P2128
P2138

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2120 Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


P2122
P2123
P2125
P2127
P2128
P2138

WIRING DIAGRAM

A149601
0.281,3.167 2.438,3.375 2.156,0.208 10 Accelerator Pedal Position Sensor 5.604,1.229 6.063,1.438 0.458,0.208 10 VCPA 5.333,1.219 5.51,1.427 0.177,0.208 10 55 5.333,0.365 5.51,0.573 0.177,0.208 10 53 5.344,2.49 5.521,2.698 0.177,0.208 10 57 5.333,0.802 5.51,1.01 0.177,0.208 10 56 5.333,1.656 5.51,1.865 0.177,0.208 10 54 5.333,2.083 5.51,2.292 0.177,0.208 10 58 5.604,0.385 6,0.594 0.396,0.208 10 VPA 5.604,0.792 6.052,1 0.448,0.208 10 EPA 5.604,2.5 6.052,2.708 0.448,0.208 10 VCP2 5.604,1.625 6.042,1.833 0.438,0.208 10 VPA2 5.604,2.052 6.198,2.26 0.594,0.208 10 EPA2 1.5,1.313 1.958,1.521 0.458,0.208 10 VCPA 1.573,0.469 1.885,0.677 0.313,0.208 10 VPA 1.573,0.896 1.917,1.104 0.344,0.208 10 EPA 1.5,2.583 1.948,2.792 0.448,0.208 10 VCP2 1.5,1.74 1.938,1.948 0.438,0.208 10 VPA2 1.5,2.156 1.927,2.365 0.427,0.208 10 EPA2 1.99,1.396 2.198,1.604 0.208,0.208 10 4 1.99,0.573 2.198,0.781 0.208,0.208 10 6 1.99,1 2.198,1.208 0.208,0.208 10 5 1.99,2.698 2.198,2.906 0.208,0.208 10 1 1.99,1.844 2.198,2.052 0.208,0.208 10 3 1.99,2.271 2.198,2.479 0.208,0.208 10 2 5.979,3.167 6.375,3.365 0.396,0.198 10 ECM 5.979,3.01 6.271,3.188 0.292,0.177 10 A61 0.281,3.01 0.5,3.198 0.219,0.188 10 A6

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 95%


Result:
Proceed to
A
B




A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (VCP2) - A61-57 (VCP2) Always Below 1 Ω
A6-2 (EPA2) - A61-58 (EPA2) Always Below 1 Ω
A6-3 (VPA2) - A61-54 (VPA2) Always Below 1 Ω
A6-4 (VCPA) - A61-55 (VCPA) Always Below 1 Ω
A6-5 (EPA) - A61-56 (EPA) Always Below 1 Ω
A6-6 (VPA) - A61-53 (VPA) Always Below 1 Ω
A6-1 (VCP2) or A61-57 (VCP2) - Body ground Always 10 kΩ or higher
A6-2 (EPA2) or A61-58 (EPA2) - Body ground Always 10 kΩ or higher
A6-3 (VPA2) or A61-54 (VPA2) - Body ground Always 10 kΩ or higher
A6-4 (VCPA) or A61-55 (VCPA) - Body ground Always 10 kΩ or higher
A6-5 (EPA) or A61-56 (EPA) - Body ground Always 10 kΩ or higher
A6-6 (VPA) or A61-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.
A200914
0.458,0.99 0.854,1.281 0.396,0.292 1.885,1.146 2.469,1.646 false 2.01,1.677 1.781,1.146 false 1.354,1.677 1.5,1.146 false 0.823,1.615 1.323,1.135 false 0,0 0.313,0.156 0.313,0.156 10 *a 0.552,1.052 0.865,1.25 0.313,0.198 10 A6 0.635,1.667 1.188,1.865 0.552,0.198 10 VCP2 1.813,1.729 2.365,1.927 0.552,0.198 10 VCPA 1.177,1.74 1.729,1.938 0.552,0.198 10 EPA2 2.354,1.688 2.906,1.885 0.552,0.198 10 EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Disconnect the accelerator pedal sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-4 (VCPA) - A6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A6-1 (VCP2) - A6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

5.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and leave the vehicle for 30 seconds.


f.

Turn the ignition switch to ON.


g.

Fully close the accelerator pedal for 3 seconds or more, then hold it partway open for 3 seconds or more, and then fully open it for 3 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END