Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the time calculated by the ECM. The glow plug is then heated, and enhances fuel combustion with a cold engine.

A129368
0.042,0 2.427,0.208 2.385,0.208 10 false Glow System Wiring Diagram 0.167,0.521 1.406,1.063 1.24,0.542 10 false from Battery 1.656,0.292 2.219,0.49 0.563,0.198 10 false GLOW 1.156,1.917 1.948,2.115 0.792,0.198 10 false Glow Plug 3.292,1.042 4.646,1.26 1.354,0.219 10 false Glow Plug Relay 5.906,0.083 6.333,0.281 0.427,0.198 10 false ECM 5.24,0.469 5.74,0.677 0.5,0.208 10 false GREL

HINT:
·

These troubleshooting procedures are for: 1) difficulty starting the engine in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after the engine is started.

·

After the engine is started, the ECM performs "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A117830
0.125,0.021 1.406,0.229 1.281,0.208 10 false After-glow System 1.667,0.948 2.719,1.146 1.052,0.198 10 false After-glow Time 2.542,0.26 3.229,0.448 0.688,0.188 10 false (Second) 2.99,1.906 4.802,2.115 1.813,0.208 10 false Engine Coolant Temperature 2.438,2.75 2.76,2.948 0.323,0.198 10 false Off 2.448,3.365 2.76,3.563 0.313,0.198 10 false Off 4.042,2.427 4.292,2.625 0.25,0.198 10 false On 4.042,3.021 4.292,3.219 0.25,0.198 10 false On 1.302,2.844 2.229,3.021 0.927,0.177 10 false Ignition Switch 1.563,3.448 2.24,3.667 0.677,0.219 10 false Glow Plug 1.354,4.031 2.26,4.24 0.906,0.208 10 false Engine Speed 2.698,4.438 3.708,4.656 1.01,0.219 10 false Starting Engine 3.74,4.302 4.771,4.479 1.031,0.177 10 false After-glow Time 5.125,3.333 5.5,3.531 0.375,0.198 10 false Off

WIRING DIAGRAM

A284168
3.146,2.729 4.521,2.927 1.375,0.198 10 false Glow Plug 5.458,0.677 5.75,0.865 0.292,0.188 10 false 58 3.146,2.573 3.438,2.76 0.292,0.188 10 false B83 2.979,0.99 3.271,1.177 0.292,0.188 10 false 2 3.76,0.99 4.052,1.177 0.292,0.188 10 false 1 3.76,1.625 4.052,1.813 0.292,0.188 10 false 3 3,1.625 3.292,1.813 0.292,0.188 10 false 4 5.896,0.521 6.385,0.708 0.49,0.188 10 false GREL 6.031,3.313 6.521,3.5 0.49,0.188 10 false B76 6.031,3.49 6.521,3.677 0.49,0.188 10 false ECM 1.156,2.708 1.708,2.917 0.552,0.208 10 false Battery 1.604,1.74 2.156,2.115 0.552,0.375 10 false GLOW 0.938,2.104 2.01,2.479 1.073,0.375 10 false FL MAIN 2.813,1.854 3.104,2.042 0.292,0.188 10 false B38 3.115,1.969 4.49,2.167 1.375,0.198 10 false Glow Plug 4.438,2.167 4.729,2.354 0.292,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


PROCEDURE

1.CHECK TERMINAL VOLTAGE (GLOW PLUG RELAY)
a.
A131566
0.396,1.01 0.833,1.271 0.438,0.26 0.115,0.031 0.302,0.198 0.188,0.167 10 *1 0.469,1.052 0.76,1.208 0.292,0.156 10 B38
*a Front view of wire harness connector
(to Glow Plug Relay)


Remove the glow plug relay assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B38-4 - Body ground Always 11 to 14 V



c.

Reinstall the glow plug relay assembly.


Result:
Proceed to
OK
NG



OK

2.INSPECT GLOW PLUG RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GLOW PLUG RELAY - BATTERY)

2.INSPECT GLOW PLUG RELAY ASSEMBLY
a.

Inspect the glow plug relay assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

REPLACE GLOW PLUG RELAY ASSEMBLY

3.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

4.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

NG

REPLACE GLOW PLUG ASSEMBLY

4.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
a.

Check the glow plug installation.

Click hereEngine / Hybrid System>2AD-FTV STARTING>GLOW PLUG>INSTALLATION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GLOW PLUG - GLOW PLUG RELAY - BODY GROUND)

NG

TIGHTEN GLOW PLUG ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (GLOW PLUG - GLOW PLUG RELAY - BODY GROUND)
a.

Remove the glow plug relay assembly.


b.

Disconnect the glow plug connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-3 - B83-1 Always Below 1 Ω
B38-1 - Body ground Always Below 1 Ω
B38-3 or B83-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the glow plug relay assembly.


e.

Reconnect the glow plug connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)
Result:
Proceed to
OK
NG


a.

Remove the glow plug relay assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-2 - B76-58 (GREL) Always Below 1 Ω
B38-2 or B76-58 (GREL) - Body ground Always 10 kΩ or higher



d.

Reinstall the glow plug relay assembly.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR