The occupant classification system detects the front passenger seat condition. It then displays the front passenger airbag and front passenger side knee airbag condition (activated/not activated) using the passenger airbag ON/OFF indicator.
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.
| Front Passenger Seat Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
| Vacant | OFF | ON | OFF |
| Adult is seated. | ON | OFF | OFF |
| Child is seated. | OFF | ON | OFF |
| Child restraint system is installed. | |||
| Occupant classification system failure | OFF | ON | ON |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON, and check the SRS warning light condition.
If passenger airbag ON/OFF indicator trouble occurs, the SRS warning light does not illuminate. If the light comes on, a DTC is stored. Troubleshoot for the DTC.
After the primary check period, the SRS warning light goes off.
The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform zero point calibration and sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Loosen the 4 installation bolts of the front seat assembly RH.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION
Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform zero point calibration and sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Read the display when the passenger side buckle switch is operated.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle SW | Front seat belt RH buckle switch | Set, Unset or NG | Set: The front seat belt RH is fastened
Unset: The front seat belt RH is not fastened NG: Data is not determined |
- |
| Tester Display |
|---|
| Passenger Buckle SW |
The GTS display changes correctly in accordance with the operation of the buckle switch.
| Result |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the occupant detection ECU and 2 rear occupant classification sensors.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the 2 rear occupant classification sensors.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Connect the cable to the negative (-) battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform zero point calibration and sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the occupant detection ECU.
Replace the front seat inner belt assembly RH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Connect the cable to the negative (-) battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform zero point calibration and sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT