Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2013.11–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM J

1AD-FTV ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the clutch start switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o entry and start system

*2: w/ entry and start system


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

16.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

3.INSPECT ST RELAY

NG

10.INSPECT CLUTCH START SWITCH ASSEMBLY
3.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.




Result:
Result Proceed to
OK A
NG (w/ stop and start system) B
NG (w/o stop and start system) C



A

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

B

C

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST relay) - B6-1 Always Below 1 Ω
3 (ST relay) or B6-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C4-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
a.
A296486
0.094,0.146 0.406,0.302 0.313,0.156 10 *1 2.073,3.51 2.385,3.667 0.313,0.156 10 *2
*1 Engine Room NO. 2 Relay Block and Junction Block Assembly
*2 ST Relay


Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - A4-1*1 Always Below 1 Ω
2 (ST relay) - F2-1*2 Always Below 1 Ω


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ entry and start system) A
OK (w/o entry and start system) B
NG C



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)

B

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2*1 Always Below 1 Ω
G82-5 (STAR) - F2-2*2 Always Below 1 Ω
G82-5 (STAR) or A4-2*1 - Body ground Always 10 kΩ or higher
G82-5 (STAR) or F2-2*2 - Body ground Always 10 kΩ or higher
A66-28 (CLL) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2*1 Always Below 1 Ω
G4-2 (ST2) - F2-2*2 Always Below 1 Ω
G4-2 (ST2) or A4-2*1 - Body ground Always 10 kΩ or higher
G4-2 (ST2) or F2-2*2 - Body ground Always 10 kΩ or higher
A66-28 (CLL) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)