Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE › 2013.11–2014.10
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0050294 TRANSMISSION CONTROL CABLE A

EA64F MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY

a.

Install the transaxle control cable assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the transaxle control cable assembly to the control cable bracket, and install 2 new clips.


c.

Connect the transaxle control cable assembly to the manual transaxle assembly, and install the 2 clips.


Hide 2.CONNECT ENGINE WIRE

a.

Connect the engine wire with bolt and clamp.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 33820B 5.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY

a.

Turn the lock nut of the transaxle control cable assembly 180° clockwise. While holding the lock nut in place, push in the stopper to lock the lock nut.

C284489C01
1.458,0.594 1.719,0.365 1.719,0.365 1.927,0.365 false 0.417,1.281 0.688,1.281 0.688,1.281 0.885,1.052 false 2,0.281 2.313,0.479 0.313,0.198 10 false *1 3.698,0.063 4.01,0.26 0.313,0.198 10 false *a 0.198,1.208 0.51,1.406 0.313,0.198 10 false *2
*1 Cable Lock *2 Lock Nut
*a Push in - -


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transaxle control cable assembly will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut counterclockwise and then push in the cable lock again.



b.

Connect the outer part of the transaxle control cable assembly to the floor shift shift lever assembly. Check that the stopper returns to the pulled-out position.

C284490C01
1.542,0.448 1.802,0.219 1.802,0.219 1.99,0.219 false 0.594,1 0.813,1 0.813,1 1.031,0.771 false 0.677,1.292 0.906,1.292 0.906,1.292 1.135,1.427 true 2.094,0.125 2.406,0.323 0.313,0.198 10 false *1 0.354,0.906 0.667,1.104 0.313,0.198 10 false *2 0.469,1.208 0.781,1.406 0.313,0.198 10 false *3
*1 Cable Lock *2 Lock Nut
*3 Floor Shift Shift Lever Assembly - -



c.
C284491C01
1.438,1.365 1.688,1.365 1.688,1.365 1.792,1.073 false 1.448,1.885 1.698,1.885 1.698,1.885 1.844,2.219 false 2.375,1 2.583,1.198 2.583,1.198 2.844,1.188 false 2.458,2.083 2.604,1.833 2.604,1.833 2.865,1.823 false 1.188,1.292 1.5,1.49 0.313,0.198 10 false *1 1.198,1.802 1.51,2 0.313,0.198 10 false *1 2.917,1.104 3.229,1.302 0.313,0.198 10 false *2 2.958,1.74 3.271,1.938 0.313,0.198 10 false *2
*1 Slider
*2 Lock Piece


Slide the slider in the direction shown in the illustration and pull out the lock piece.


d.
C284493C01
1.323,1.271 1.188,0.823 1.188,0.823 0.948,0.823 true 2.833,1.24 2.521,0.25 2.521,0.25 2.281,0.25 true 0.667,0.729 0.979,0.927 0.313,0.198 10 true *1 1.906,0.167 2.219,0.365 0.313,0.198 10 true *2
*1 Select Control Cable
*2 Shift Control Cable


Connect the shift control cable to the floor shift shift lever assembly.


e.

Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.


f.
C284492

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



g.
C284494

Install a new clip to the select control cable.

HINT:

Install a new clip.



Hide 58901A 6.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY