Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT › from 2015.04
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046816 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16620 1.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

When replacing the V-ribbed belt tensioner assembly with a new one.

i.

Install the V-ribbed belt tensioner assembly to the engine assembly with the 2 bolts.

NOTICE:

Make sure to install a new V-ribbed belt tensioner assembly with the pin and white cover installed to it.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


ii.

Remove the white cover.


iii.

Rotate the V-ribbed belt tensioner assembly slightly clockwise and remove the pin that is used to keep the spring compressed.

NOTICE:
·

Do not forcibly rotate the V-ribbed belt tensioner assembly to the V-ribbed belt installation position with the pin installed.

·

Do not apply or add any oil or grease to the V-ribbed belt tensioner assembly.



HINT:

When installing the V-ribbed belt, rotate the V-ribbed belt tensioner assembly clockwise again with the pin removed, and secure the V-ribbed belt tensioner assembly using a 5 mm bi-hexagon wrench.




b.

When reusing the V-ribbed belt tensioner assembly.

i.

Check that the pin with a diameter of 3.0 mm (0.118 in.) is installed to the V-ribbed belt tensioner assembly.


ii.

Install the V-ribbed belt tensioner assembly to the engine assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


iii.

Rotate the V-ribbed belt tensioner assembly slightly clockwise and remove the pin with a diameter of 3.0 mm (0.118 in.) that is used to keep the spring compressed.

NOTICE:

Do not forcibly rotate the V-ribbed belt tensioner assembly to the V-ribbed belt installation position with the pin with a diameter of 3.0 mm (0.118 in.) installed.


HINT:

When installing the V-ribbed belt, rotate the V-ribbed belt tensioner assembly clockwise again with the pin with a diameter of 3.0 mm (0.118 in.) removed, and secure the V-ribbed belt tensioner assembly using a 5 mm bi-hexagon wrench.




Hide 89429F 2.INSTALL ENGINE OIL TEMPERATURE SENSOR

Hide 12551A 3.INSTALL NO. 1 VACUUM PUMP BRACKET

a.

Install a new gasket and the No. 1 vacuum pump bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 29300 4.INSTALL VACUUM PUMP ASSEMBLY

Hide 44774 5.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 16268 9.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16262 10.INSTALL WATER INLET HOSE

a.

Install the water inlet hose, and slide the 2 clamps to secure the hose.


Hide 16261 11.INSTALL WATER BY-PASS HOSE

a.

Install the water by-pass hose, and slide the clamp to secure the hose.


Hide 16267 12.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the water inlet housing, and slide the clamp to secure the hose.


Hide 12261 13.INSTALL PCV HOSE

a.

Install the PCV hose to the PCV valve and slide the clamp to secure it.


Hide 16279 14.INSTALL NO. 3 WATER BY-PASS PIPE (for CVT)

a.

Install a new gasket and the No. 3 water by-pass pipe with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11492D 15.INSTALL NO. 1 SEAL PLATE (for Manual Transaxle)

a.

Install the No. 1 seal plate and new gasket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17167 18.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 19.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250 20.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807V 21.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 22.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 23.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 24.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 87245A 26.INSTALL HEATER WATER INLET HOSE

a.

Connect the heater water inlet hose to the cylinder head sub-assembly, and slide the clamp to secure the hose.


Hide 87246A 27.INSTALL HEATER WATER OUTLET HOSE

a.

Connect the heater water outlet hose to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.


b.

Attach the 2 hose clamps to connect the heater water outlet hose to the heater water inlet hose.


Hide 22210 29.INSTALL THROTTLE BODY ASSEMBLY

Hide 30.INSTALL ENGINE WIRE