When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.
Refer to the SRS precaution before troubleshooting.
w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION
w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: "+" shift paddle operated and held (up-shift) ·
OFF: "+" shift paddle not operated (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: "-" shift paddle operated and held (down-shift) ·
OFF: "-" shift paddle not operated (down-shift) |
- |
| Tester Display |
|---|
| Sports Shift Up SW |
| Sports Shift Down SW |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Disconnect the shift lever assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-42 (SFTU) - Body ground | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| A62-42 (SFTU) - Body ground | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| A62-43 (SFTD) - Body ground | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| A62-43 (SFTD) - Body ground | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly) |
Disconnect the spiral cable with sensor sub-assembly connector.
for Dual Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL
for Single Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G8 spiral cable with sensor sub-assembly connector.
for Dual Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL
for Single Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL
Disconnect the A62 ECM connector.
Disconnect the G36 shift lever assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-7 (SDN) - A62-43 (SFTD) | Always | Below 1 Ω |
| G8-14 (SUP) - A62-42 (SFTU) | Always | Below 1 Ω |
| G8-7 (SDN) or A62-43 (SFTD) - Body ground | Always | 10 kΩ or higher |
| G8-14 (SUP) or A62-42 (SFTU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Steering Pad Switch Assembly Connector
(to Spiral Cable with Sensor Sub-assembly) |
Disconnect the steering pad switch connector.
for Dual Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD(for Dual Type)>REMOVAL
for Single Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD(for Single Type)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z1-6 (SUP) - z1-7 (ECC) | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| z1-6 (SUP) - z1-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z1-12 (SDN) - z1-7 (ECC) | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| z1-12 (SDN) - z1-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable with sensor sub-assembly.
for Dual Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>INSPECTION
for Single Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Dual Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL
for Single Type: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Shift Paddle Switch LH |
Remove the shift paddle switch LH.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SFTD - ECC | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SFTD - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| SFTD - ECC1 | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SFTD - ECC1 | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Paddle Switch RH |
Remove the shift paddle switch RH.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SFTU - ECC1 | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| SFTU - ECC1 | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Switch Wire
(to Steering Pad Switch Assembly) |
Disconnect the No. 1 switch wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SFTD - ECC | "-" shift paddle operated and held (down-shift) | Below 2.5 Ω |
| SFTD - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| SFTU - ECC | "+" shift paddle operated and held (up-shift) | Below 2.5 Ω |
| SFTU - ECC | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG