When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0300 | Random / Multiple Cylinder Misfire Detected | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0301 | Cylinder 1 Misfire Detected | Misfiring of the No. 1 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0302 | Cylinder 2 Misfire Detected | Misfiring of the No. 2 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0303 | Cylinder 3 Misfire Detected | Misfiring of the No. 3 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0304 | Cylinder 4 Misfire Detected | Misfiring of the No. 4 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).
An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Switch the ECM from normal mode to check mode (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.
| Engine Speed (rpm) | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the ignition switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Refer to DTC P0102 (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>P0102).
Refer to Fuel Injector Circuit (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the "Fuel Cut Elps Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the valve rocker arm will become loose and a fire could start, so check that the valve rocker arm is properly attached (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).
By clearing the DTC, "Fuel Cut Elps Time" will be cleared.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or more).
When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
PCV valve and hose are correctly connected and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
| Tester Display |
|---|
| Misfire RPM |
| Misfire Load |
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
| Tester Display |
|---|
| Cylinder #1 Misfire Count |
| Cylinder #2 Misfire Count |
| Cylinder #3 Misfire Count |
| Cylinder #4 Misfire Count |
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the read value using GTS (Misfire RPM and Misfire Load) procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
If the freeze frame data record of the Engine Run Time is less than 120 seconds, the misfire may be detected immediately after the engine is started.
A
B
Inspect the spark plug of the misfiring cylinder (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after replacing the spark plug (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B93-98 (#10) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-95 (#20) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-96 (#30) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-97 (#40) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repairs" after replacing the fuel injector assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks (Click here Engine / Hybrid System>3ZR-FAE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
| Tester Display |
|---|
| Engine Speed |
| MAF |
| Coolant Temp |
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| MAF | Shift lever position: N
A/C: Off Engine Speed: 3000 rpm |
Between 6.5 gm/sec and 10.5 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
Check the intake system for vacuum leaks (Click here Engine / Hybrid System>3ZR-FAE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
| Tester Display |
|---|
| Engine Speed |
| MAF |
| Coolant Temp |
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| MAF | Shift lever position: N
A/C: Off Engine Speed: 3000 rpm |
Between 6.5 gm/sec and 10.5 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spark plug of the misfiring cylinder (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after replacing the spark plug (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B93-98 (#10) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-95 (#20) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-96 (#30) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| B93-97 (#40) - B93-57 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain (Click here Engine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTC is not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B1-5 (VG) - B93-137 (VG) | Always | Below 1 Ω |
| B1-4 (E2G) - B93-104 (E2G) | Always | Below 1 Ω |
| B1-5 (VG) or B93-137 (VG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).
If the results of the inspections performed in steps 13 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Warm up the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTC is not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
Perform "Inspection After Repair" after replacing the fuel pump (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG