Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  B228A  Engine Speed Signal Circuit  P0335  Crankshaft Position Sensor Circuit Malfunction (NE Signal)  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

HINT:
·

DTC B2286 is not stored for vehicles with stop and start system.

·

DTC B228A is stored only for vehicles with stop and start system.

·

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2286 Runnable Signal Malfunction The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

SFI system

·

ECD system

·

Wire harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, then start the engine and maintain an engine speed of 1000 rpm or more for 20 seconds or more.
B228A Engine Speed Signal Circuit The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1- trip detection logic*) do not match.
·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

SFI system

·

ECD system

·

Wire harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, and then start the engine.
Make sure that the engine speed is 1000 rpm or more for 20 seconds or more after starting the engine.
P0335 Crankshaft Position Sensor Circuit Malfunction (NE Signal) The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

SFI system

·

ECD system

·

Wire harness or connector


Allow the engine to idle for 10 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When the signal sent via either the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the engine switch is turned on (IG).)

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the engine switch has been turned off.


·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it is determined that the malfunction is not in CAN communication but in the direct line (NE).

1.

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

2.

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.

1.

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

2.

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE).

1.

When the engine switch is pressed, the engine stops cranking after 6 seconds.

2.

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.





Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2286
B228A
P0335
Power Source Control:
·

Engine Condition


Starting Control:
·

Engine Speed


-

WIRING DIAGRAM

C278635E02
2.667,0.5 3.615,0.698 0.948,0.198 10 from Battery 4.146,0.677 4.583,0.875 0.438,0.198 10 AM2 5.396,0.521 5.833,0.719 0.438,0.198 10 +B 5.406,1.021 5.844,1.219 0.438,0.198 10 NE 5.156,2.313 5.594,2.51 0.438,0.198 10 11 5.135,2.948 5.573,3.146 0.438,0.198 10 G82 5.146,0.917 5.583,1.115 0.438,0.198 10 16 5.177,0.417 5.615,0.615 0.438,0.198 10 2 5.135,3.094 6.729,3.521 1.594,0.427 10 Certification ECU (Smart Key ECU assembly) 5.396,2.448 5.833,2.646 0.438,0.198 10 E 2.427,1.031 2.771,1.177 0.344,0.146 10 A62 2.75,1.031 3.115,1.188 0.365,0.156 10 A62 3.083,1.031 3.469,1.198 0.385,0.167 10 A61 2.01,1.021 2.385,1.198 0.375,0.177 10 NEO 2.479,0.833 2.74,1.01 0.26,0.177 10 30 2.802,0.833 3.063,1.01 0.26,0.177 10 45 3.135,0.844 3.396,1.021 0.26,0.177 10 10 3.125,1.208 3.385,1.385 0.26,0.177 10 *3 2.49,1.219 2.75,1.396 0.26,0.177 10 *1 2.823,1.208 3.083,1.385 0.26,0.177 10 *2 1.542,1.844 1.979,2.042 0.438,0.198 10 ECM 1.219,3.354 3.292,3.583 2.073,0.229 10 : CAN Communication Line 0.427,2.521 2.5,2.75 2.073,0.229 10 *1: for 3ZR-FE, 3ZR-FAE 0.427,2.771 2.5,3 2.073,0.229 10 *2: for 2AR-FE 0.427,3.021 2.917,3.208 2.49,0.188 10 *3: for 1AD-FTV, 2AD-FHV, 2AD-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.READ VALUE USING GTS (ENGINE CONDITION, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Condition Engine state Stop or Run Run: Engine running
Stop: Engine stopped
-
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 16383 r/min Fluctuates in accordance with engine speed -
Body Electrical > Power Source Control > Data List
Tester Display
Engine Condition
50003 223 15
Body Electrical > Starting Control > Data List
Tester Display
Engine Speed
50003 221 8
OK:

The Data List item changes in accordance with the engine condition.



Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV (for DPF))
NG (for 2AD-FTV (for CCo))
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG (for 1AD-FTV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FHV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FTV (for DPF))

NG (for 2AD-FTV (for CCo))

NG (for 2AR-FE)

NG (for 3ZR-FAE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 3ZR-FE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C38
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 false *a 2.521,1.74 2.906,1.885 0.385,0.146 10 false E 0.583,1.375 1.031,1.563 0.448,0.188 10 false G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A61 or A62 connector from the ECM.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3ZR-FE, 3ZR-FAE:
Tester Connection Condition Specified Condition
G82-16 (NE) - A62-30 (NEO) Always Below 1 Ω
G82-16 (NE) or A62-30 (NEO) - Body ground 10 kΩ or higher

for 2AR-FE:
Tester Connection Condition Specified Condition
G82-16 (NE) - A62-45 (NEO) Always Below 1 Ω
G82-16 (NE) or A62-45 (NEO) - Body ground 10 kΩ or higher

for 1AD-FTV, 2AD-FHV, 2AD-FTV:
Tester Connection Condition Specified Condition
G82-16 (NE) - A61-10 (NEO) Always Below 1 Ω
G82-16 (NE) or A61-10 (NEO) - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B268627C10
1.385,0.25 1.823,0.5 0.438,0.25 1.042,1.635 1.458,1.219 false 0.302,0.125 0.615,0.281 0.313,0.156 10 *a 1.458,0.302 1.958,0.469 0.5,0.167 10 G82 0.906,1.667 1.406,1.833 0.5,0.167 10 NE
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Check the engine speed input signal waveform at the terminal of the certification ECU.

Standard Frequency:
Tester Connection Condition Specified Condition
G82-16 (NE) - Body ground Engine stopped No pulse generated
Engine running Pulse generated



Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV (for DPF))
NG (for 2AD-FTV (for CCo))
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG (for 1AD-FTV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FHV)

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 2AD-FTV (for DPF))

NG (for 2AD-FTV (for CCo))

NG (for 2AR-FE)

NG (for 3ZR-FAE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG (for 3ZR-FE)

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)