Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Immobiliser Malfunction  


DESCRIPTION

·

w/ Multi-information Display (Dot Display Type):

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

·

w/ Multi-information Display (Segment Display Type):

When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Immobiliser Malfunction Either condition is met (1 trip detection logic*3):
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.


·

ID code box (immobiliser code ECU)*1

·

Certification ECU (smart key ECU assembly)*2

·

ECM

·

Harness or connector

·

Telephone transceiver assembly*6


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*4 and the brake pedal*4 or clutch pedal*5 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: Only output while a malfunction is present.

*4: except Manual Transaxle

*5: for Manual Transaxle

*6: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

1. w/o Blocking System


B278902E05
1.104,1.646 1.573,1.885 0.469,0.24 10 false A62*3 1.104,1.969 1.646,2.344 0.542,0.375 10 false ECM 5.469,0.573 5.865,0.76 0.396,0.188 10 false EFIO 5.469,2.854 5.865,3.042 0.396,0.188 10 false EFIO 5.469,1.031 5.865,1.219 0.396,0.188 10 false EFII 5.469,3.406 5.865,3.594 0.396,0.188 10 false EFII 1.438,0.573 1.833,0.76 0.396,0.188 10 false IMI 1.406,1.042 1.802,1.229 0.396,0.188 10 false IMO 1.802,0.5 2.5,0.677 0.698,0.177 10 false 28*3 1.802,0.969 3.24,1.177 1.438,0.208 10 false 29*3, *5, 45*3, *6 5.198,0.49 5.49,0.698 0.292,0.208 10 false 13 5.208,0.969 5.5,1.177 0.292,0.208 10 false 14 5.292,3.302 5.417,3.479 0.125,0.177 10 false 3 5.292,2.729 5.417,2.906 0.125,0.177 10 false 4 5.094,1.552 5.542,1.844 0.448,0.292 10 false G82 5.094,3.792 5.51,4.146 0.417,0.354 10 false G44 5.094,1.719 6.635,2.042 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.99 6.677,4.385 1.583,0.396 10 false ID Code Box (Immobiliser Code ECU) 0.052,3.563 3.438,3.802 3.385,0.24 10 false *1: w/ Multi-information Display (Dot Display Type) 0.052,3.844 3.74,4.063 3.688,0.219 10 false *2: w/ Multi-information Display (Segment Display Type) 4.396,0.448 4.656,0.74 0.26,0.292 10 false *2 4.396,0.927 4.688,1.177 0.292,0.25 10 false *2 3.188,2.208 3.74,2.698 0.552,0.49 10 false *1 4.042,2.208 4.438,2.542 0.396,0.333 10 false *1 1.104,1.802 1.573,2.042 0.469,0.24 10 false A61*4 1.792,0.688 2.49,0.865 0.698,0.177 10 false 16*4 1.792,1.177 2.49,1.354 0.698,0.177 10 false 15*4 0.052,4.125 3.74,4.344 3.688,0.219 10 false *3: for Gasoline 0.052,4.406 3.74,4.625 3.688,0.219 10 false *4: for Diesel 1.573,4.135 5.26,4.354 3.688,0.219 10 false *5: except 3ZR-FAE 1.594,4.385 5.281,4.604 3.688,0.219 10 false *6: for 3ZR-FAE


2. w/ Blocking System


B278903E02
1.104,1.885 1.406,2.063 0.302,0.177 10 A62 1.104,2.042 1.563,2.219 0.458,0.177 10 ECM 5.49,1.26 5.885,1.448 0.396,0.188 10 EFIO 3.198,0.781 3.594,0.969 0.396,0.188 10 BLK2 3.198,1.26 3.594,1.448 0.396,0.188 10 BLK3 3.656,1.26 4.052,1.448 0.396,0.188 10 BLK4 5.49,0.771 5.885,0.958 0.396,0.188 10 EFII 1.521,1.25 1.771,1.438 0.25,0.188 10 IMI 1.448,0.781 1.844,0.969 0.396,0.188 10 IMO 1.771,0.698 1.99,0.875 0.219,0.177 10 29 1.771,1.156 2,1.333 0.229,0.177 10 28 5.219,1.177 5.51,1.385 0.292,0.208 10 13 3.656,0.781 4.052,0.969 0.396,0.188 10 BLK1 4.063,0.708 4.198,0.854 0.135,0.146 10 1 3.031,0.698 3.167,0.844 0.135,0.146 10 7 3.031,1.188 3.167,1.333 0.135,0.146 10 8 4.063,1.177 4.198,1.323 0.135,0.146 10 2 5.229,0.708 5.521,0.917 0.292,0.208 10 14 5.104,1.792 5.49,1.979 0.385,0.188 10 G82 2.906,1.792 3.292,1.979 0.385,0.188 10 G58 5.104,1.958 6.646,2.281 1.542,0.323 10 Certification ECU (Smart Key ECU Assembly) 2.906,1.958 4.333,2.281 1.427,0.323 10 Telephone Transceiver Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly)*1, ID code box (immobiliser code ECU)*2 or telephone transceiver assembly*3, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.*3


*1: w/ Multi-information Display (Segment Display Type)

*2: w/ Multi-information Display (Dot Display Type)

*3: w/ Blocking System



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Proceed to
w/o Blocking System
w/ Blocking System



w/o Blocking System

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

w/ Blocking System

10.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: for Gasoline

*4: for Diesel


a.

Disconnect the G44 ID code box (immobiliser code ECU) connector.*1


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.*2


c.

Disconnect the A62*3 or A61*4 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Gasoline
Tester Connection Condition Specified Condition
G44-3 (EFII) - A62-29 (IMO)*1, *3 Always Below 1 Ω
G44-3 (EFII) - A62-45 (IMO)*1, *4
G82-14 (EFII) - A62-29 (IMO)*2
A62-29 (IMO) - Body ground*3 Always 10 kΩ or higher
A62-45 (IMO) - Body ground*4
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G82-14 (EFII) - Body ground*2 Always 10 kΩ or higher
G44-4 (EFIO) - A62-28 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A62-28 (IMI)*2
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher

for Diesel
Tester Connection Condition Specified Condition
G44-3 (EFII) - A61-15 (IMO)*1 Always Below 1 Ω
G82-14 (EFII) - A61-15 (IMO)*2
A61-15 (IMO) - Body ground Always 10 kΩ or higher
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G82-14 (EFII) - Body ground*2 Always 10 kΩ or higher
G44-4 (EFIO) - A61-16 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A61-16 (IMI)*2
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher


*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: except 3ZR-FAE

*4: for 3ZR-FAE



Result:
Proceed to
OK
NG



OK

3.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2799 is not output
B2799 is output
Other DTCs are output



B2799 is not output

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

B2799 is output

6.REPLACE ECM

Other DTCs are output

6.REPLACE ECM

NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG (w/ Multi-information Display [Dot Display Type])
NG (w/ Multi-information Display [Segment Display Type])



OK

END (ECM WAS DEFECTIVE)

NG (w/ Multi-information Display [Dot Display Type])

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG (w/ Multi-information Display [Segment Display Type])

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the A62 ECM connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-29 (IMO) - G58-7 (BLK2) Always Below 1 Ω
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G58-7 (BLK2) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - G58-8 (BLK3) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G58-8 (BLK3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-14 (EFII) - G58-1 (BLK1) Always Below 1 Ω
G82-14 (EFII) - Body ground Always 10 kΩ or higher
G58-1 (BLK1) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - G58-2 (BLK4) Always Below 1 Ω
G82-13 (EFIO) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2799 is not output
B2799 is output
Other DTCs are output



B2799 is not output

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

B2799 is output

15.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

Other DTCs are output

15.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Temporarily replace the telephone transceiver assembly with a new or known good one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.REGISTER ECU COMMUNICATION ID
16.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

18.CHECK FOR DTC
18.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2799 is not output
B2799 is output



B2799 is not output

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE)

B2799 is output

6.REPLACE ECM