Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM

·

Telephone transceiver assembly*3


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.



*3: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

1. w/o Blocking System


B341473E11
2.021,0.344 3.594,0.635 1.573,0.292 10 false 29*1, *3, 45*1, *4 2.01,0.604 2.396,0.771 0.385,0.167 10 false 15*2 2.031,1.104 2.417,1.271 0.385,0.167 10 false 28*1 2.021,1.375 2.406,1.542 0.385,0.167 10 false 16*2 1.667,0.469 2.052,0.635 0.385,0.167 10 false IMO 1.708,1.229 2.094,1.396 0.385,0.167 10 false IMI 5.438,0.375 5.667,0.552 0.229,0.177 10 false 12 5.438,1.125 5.667,1.302 0.229,0.177 10 false 13 5.719,0.49 6.104,0.656 0.385,0.167 10 false EFII 5.729,1.24 6.115,1.406 0.385,0.167 10 false EFIO 1.281,1.979 1.948,2.156 0.667,0.177 10 false A62*1 1.281,2.125 2.01,2.292 0.729,0.167 10 false A61*2 1.281,2.281 2.146,2.469 0.865,0.188 10 false ECM 2.948,1.667 4.146,1.865 1.198,0.198 10 false *1: for Gasoline 2.969,1.917 4.167,2.115 1.198,0.198 10 false *2: for Diesel 5.594,1.99 5.979,2.156 0.385,0.167 10 false G88 5.594,2.156 6.74,2.323 1.146,0.167 10 false Transponder Key ECU Assembly 2.969,2.167 4.75,2.406 1.781,0.24 10 false *3: except 3ZR-FAE 2.979,2.427 4.229,2.646 1.25,0.219 10 false *4: for 3ZR-FAE


2. w/ Blocking System


B278903E03
1.104,1.885 1.406,2.063 0.302,0.177 10 A62 1.104,2.042 1.563,2.219 0.458,0.177 10 ECM 5.49,1.24 5.885,1.427 0.396,0.188 10 EFIO 3.198,0.781 3.594,0.969 0.396,0.188 10 BLK2 3.198,1.26 3.594,1.448 0.396,0.188 10 BLK3 3.656,1.26 4.052,1.448 0.396,0.188 10 BLK4 5.49,0.771 5.885,0.958 0.396,0.188 10 EFII 1.521,1.25 1.771,1.438 0.25,0.188 10 IMI 1.448,0.781 1.844,0.969 0.396,0.188 10 IMO 1.771,0.698 1.99,0.875 0.219,0.177 10 29 1.771,1.156 2,1.333 0.229,0.177 10 28 5.219,1.156 5.51,1.365 0.292,0.208 10 13 3.656,0.781 4.052,0.969 0.396,0.188 10 BLK1 4.063,0.708 4.198,0.854 0.135,0.146 10 1 3.031,0.698 3.167,0.844 0.135,0.146 10 7 3.031,1.167 3.167,1.313 0.135,0.146 10 8 4.063,1.156 4.198,1.302 0.135,0.146 10 2 5.229,0.688 5.521,0.896 0.292,0.208 10 12 5.104,1.792 5.49,1.979 0.385,0.188 10 G88 2.906,1.792 3.292,1.979 0.385,0.188 10 G58 5.104,1.958 6.521,2.333 1.417,0.375 10 Transponder Key ECU Assembly 2.906,1.958 4.333,2.281 1.427,0.323 10 Telephone Transceiver Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Proceed to
OK
NG (DTC B2799 is output)
NG (Other DTCs are output)



OK

NG (DTC B2799 is output)

3.REGISTER ECU COMMUNICATION ID

NG (Other DTCs are output)

3.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

5.INSPECT ECM (IMO TERMINAL VOLTAGE)
5.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the A62*1 or A61*2 ECM connector.

*1: for Gasoline

*2: for Diesel



b.

Turn the ignition switch to ON.


c.
B340993C02
0.229,0.802 0.635,1.063 0.406,0.26 0.292,2.344 0.698,2.604 0.406,0.26 2.125,0.99 2.656,0.771 false 2.01,2.229 2.667,2.635 false 2.198,1.073 2.635,1.26 false 0.313,0.865 0.625,1.021 0.313,0.156 10 false A62 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.385,2.406 0.698,2.563 0.313,0.156 10 false A61 0.698,0.875 1.01,1.031 0.313,0.156 10 false *A 0.74,2.427 1.052,2.583 0.313,0.156 10 false *B 2.698,0.688 3.292,0.896 0.594,0.208 10 false IMO*C 2.635,2.708 3,2.865 0.365,0.156 10 false IMO 2.698,1.188 3.292,1.396 0.594,0.208 10 false IMO*D
*A for Gasoline
*B for Diesel
*C except 3ZR-FAE
*D for 3ZR-FAE
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
A62-29 (IMO) - Body ground*1, *3
A62-45 (IMO) - Body ground*1, *4
A61-15 (IMO) - Body ground*2
Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for Gasoline

*2: for Diesel

*3: except 3ZR-FAE

*4: for 3ZR-FAE



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) (w/ Blocking System) A
Terminal IMO stuck low (2.4 V or less) (w/o Blocking System) B
Terminal IMO stuck high (12 V) or abnormal waveform (w/o Blocking System) C
Terminal IMO stuck high (12 V) or abnormal waveform (w/ Blocking System) D



A

6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU AND ECM)

B

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

C

15.REPLACE ECM

D

18.REPLACE ECM
6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU AND ECM)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G58 transponder key ECU assembly connector.


c.

Disconnect the A62 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - G88-12 (EFII) Always Below 1 Ω
G58-7 (BLK2) - A62-29 (IMO) Always Below 1 Ω
G58-8 (BLK3) - A62-28 (IMI) Always Below 1 Ω
G58-2 (BLK4) - G88-13 (EFIO) Always Below 1 Ω
G58-1 (BLK1) - Body ground Always 10 kΩ or higher
G58-7 (BLK2) - Body ground Always 10 kΩ or higher
G58-8 (BLK3) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher
A62-29 (IMO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

9.REPLACE ECM
9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 2AR-FE:

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL

for 3ZR-FE:

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62*1 or A61*2 ECM connector.

*1: for Gasoline

*2: for Diesel



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Gasoline:
Tester Connection Condition Specified Condition

*1: except 3ZR-FAE

*2: for 3ZR-FAE

G88-12 (EFII) - A62-29 (IMO)*1 Always Below 1 Ω
G88-12 (EFII) - A62-45 (IMO)*2 Always Below 1 Ω
G88-12 (EFII) - Body ground Always 10 kΩ or higher
A62-29 (IMO) - Body ground*1 Always 10 kΩ or higher
A62-45 (IMO) - Body ground*2 Always 10 kΩ or higher
G88-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher

for Diesel:
Tester Connection Condition Specified Condition
G88-12 (EFII) - A61-15 (IMO) Always Below 1 Ω
G88-12 (EFII) - Body ground Always 10 kΩ or higher
A61-15 (IMO) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - A61-16 (IMI) Always Below 1 Ω
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
A61-16 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 1AD-FTV)
NG (for 2AD-FTV)
NG (for 2AD-FHV)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 1AD-FTV)

NG (for 2AD-FTV)

NG (for 2AD-FHV)

15.REPLACE ECM

NEXT

16.REGISTER ECU COMMUNICATION ID
16.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER ENGINE STARTS
17.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

18.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 2AR-FE:

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL

for 3ZR-FE:

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.REGISTER ECU COMMUNICATION ID
19.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER ENGINE STARTS
20.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

21.REPLACE TRANSPONDER KEY ECU ASSEMBLY
21.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER ENGINE STARTS
22.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY