Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0030  HO2S Heater Control Circuit Bank 1 Sensor 1  


DESCRIPTION

The air fuel ratio sensor is a broadband air fuel ratio sensor. The broadband air fuel ratio sensor measures the remaining oxygen in the exhaust gas. Fluctuations in the value of the remaining oxygen are sent to the ECM as a voltage signal.

The air fuel ratio sensor is used as both a control sensor and monitoring sensor in diesel engines. The lambda air fuel ratio sensor is necessary to ensure the value of the exhaust gas is within compliance. The air fuel ratio sensor is necessary for calculating the average amount value for the injectors. The lambda air fuel ratio sensor measures the air fuel ratio. If there is a deviation, the ECM changes the exhaust gas recirculation rate to optimize the air fuel ratio. Adjusting the average amount value is not a control operation which is performed. air fuel ratio sensor deviation is "learned" to the characteristic map and stored temporarily by the ECM.

The sensor system of the broadband air fuel ratio sensor is composed of several thin layers of zirconium dioxide ceramic. The heating element within the laminate ensures the required operating temperature of at least 760°C. The broadband air fuel ratio sensor includes two cells, a measurement cell and a reference cell. These two cells are coated in electrodes made of platinum.

HINT:
·

Although the DTC titles say HO2S heater, these DTCs relate to the air fuel ratio sensor heater.

·

Sensor 1 is the sensor installed in the exhaust manifold converter in the front of the catalytic converter.

·

Sensor 2 is the sensor installed in the exhaust manifold converter in the rear of the catalytic converter.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0030 HO2S Heater Control Circuit Bank 1 Sensor 1 Ground short in air fuel ratio sensor (for sensor 1) heater circuit for 2 seconds.
(3 trip detection logic)
·

Short in air fuel ratio sensor (for sensor 1) heater circuit

·

Air fuel ratio sensor (for sensor 1)

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A351167E03
1.25,1.646 1.635,2.177 0.385,0.531 10 false EFI MAIN NO. 1 1.365,0.875 2.74,1.073 1.375,0.198 10 false EFI NO. 2 0.531,1.448 0.927,1.844 0.396,0.396 10 false 3 1.021,2.24 1.417,2.635 0.396,0.396 10 false 2 0.531,2.24 0.927,2.635 0.396,0.396 10 false 5 1.01,1.427 1.406,1.823 0.396,0.396 10 false 1 0.781,3.052 1.417,3.49 0.635,0.438 10 false EFI MAIN NO. 1 0.792,4.073 1.521,4.365 0.729,0.292 10 false FL MAIN 0.917,5.052 1.646,5.344 0.729,0.292 10 false Battery 2.677,3 3.333,3.26 0.656,0.26 10 false B107 2.667,3.167 5.042,3.438 2.375,0.271 10 false Air Fuel Ratio Sensor (for Sensor 1) 3.167,0.698 4.542,0.896 1.375,0.198 10 false +B 3.01,0.594 4.385,0.792 1.375,0.198 10 false 4 5.667,0.49 6.135,0.719 0.469,0.229 10 false 127 3.76,1.156 4.229,1.385 0.469,0.229 10 false AF1- 3.729,1.594 4.198,1.823 0.469,0.229 10 false HAF1 3.833,2.167 4.302,2.396 0.469,0.229 10 false TR1 3.844,2.615 4.313,2.844 0.469,0.229 10 false RE1 4.188,0.594 4.417,0.865 0.229,0.271 10 false 1 4.188,1.052 4.417,1.323 0.229,0.271 10 false 2 4.188,1.51 4.417,1.781 0.229,0.271 10 false 3 4.177,2.073 4.406,2.344 0.229,0.271 10 false 5 4.188,2.542 4.417,2.813 0.229,0.271 10 false 6 5.615,0.698 6.229,0.948 0.615,0.25 10 false B112 5.625,1.167 6.24,1.417 0.615,0.25 10 false B112 5.615,1.604 6.229,1.854 0.615,0.25 10 false B112 5.615,2.177 6.229,2.427 0.615,0.25 10 false B112 5.615,2.625 6.229,2.875 0.615,0.25 10 false B112 5.677,0.958 6.146,1.188 0.469,0.229 10 false 126 5.708,1.417 6.177,1.646 0.469,0.229 10 false 46 5.667,1.969 6.135,2.198 0.469,0.229 10 false 128 5.667,2.438 6.135,2.667 0.469,0.229 10 false 125 3.771,0.708 4.24,0.938 0.469,0.229 10 false AF1+ 6.031,0.688 6.5,0.917 0.469,0.229 10 false AF1+ 6.042,1.167 6.51,1.396 0.469,0.229 10 false AF1- 6.042,1.604 6.51,1.833 0.469,0.229 10 false HAF1 6.052,2.156 6.521,2.385 0.469,0.229 10 false TR1 6.042,2.635 6.51,2.865 0.469,0.229 10 false RE1 3.188,3.969 3.552,4.219 0.365,0.25 10 false +B 3.01,3.854 3.24,4.125 0.229,0.271 10 false 4 4.188,3.75 4.417,4.021 0.229,0.271 10 false 1 3.771,3.865 4.24,4.094 0.469,0.229 10 false AF2+ 3.771,4.354 4.24,4.583 0.469,0.229 10 false AF2- 3.729,4.781 4.198,5.01 0.469,0.229 10 false HAF2 3.844,5.365 4.313,5.594 0.469,0.229 10 false TR2 3.833,5.792 4.302,6.021 0.469,0.229 10 false RE2 6.031,3.844 6.5,4.073 0.469,0.229 10 false AF2+ 6.052,4.333 6.521,4.563 0.469,0.229 10 false AF2- 6.042,4.76 6.51,4.99 0.469,0.229 10 false HAF2 6.042,5.323 6.51,5.552 0.469,0.229 10 false TR2 6.031,5.771 6.5,6 0.469,0.229 10 false RE2 5.615,3.865 6.229,4.115 0.615,0.25 10 false B112 5.615,4.344 6.229,4.594 0.615,0.25 10 false B112 5.615,4.771 6.229,5.021 0.615,0.25 10 false B112 5.625,5.354 6.24,5.604 0.615,0.25 10 false B112 5.615,5.802 6.229,6.052 0.615,0.25 10 false B112 5.667,3.677 6.135,3.906 0.469,0.229 10 false 130 5.677,4.146 6.146,4.375 0.469,0.229 10 false 133 5.708,4.594 6.177,4.823 0.469,0.229 10 false 17 5.656,5.156 6.125,5.385 0.469,0.229 10 false 131 5.656,5.604 6.125,5.833 0.469,0.229 10 false 134 5.688,6.813 6.302,7.063 0.615,0.25 10 false A62 5.771,6.635 6.24,6.865 0.469,0.229 10 false 9 5.688,7.365 6.302,7.615 0.615,0.25 10 false A62 5.781,7.167 6.25,7.396 0.469,0.229 10 false 4 6.031,6.802 6.5,7.031 0.469,0.229 10 false MREL 6.031,7.365 6.5,7.594 0.469,0.229 10 false E1 6.198,8.021 6.667,8.25 0.469,0.229 10 false ECM 2.615,6.271 4.99,6.542 2.375,0.271 10 false Air Fuel Ratio Sensor (for Sensor 2) 2.594,6.104 3.25,6.365 0.656,0.26 10 false B133 4.188,4.24 4.417,4.51 0.229,0.271 10 false 2 4.188,4.688 4.417,4.958 0.229,0.271 10 false 3 4.198,5.25 4.427,5.521 0.229,0.271 10 false 5 4.188,5.688 4.417,5.958 0.229,0.271 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR ((FOR SENSOR 1) (HEATER RESISTANCE))
a.

Inspect the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)

NG

9.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B107-1 (AF1+) - B112-127 (AF1+) Always Below 1 Ω
B107-2 (AF1-) - B112-126 (AF1-) Always Below 1 Ω
B107-3 (HAF1) - B112-46 (HAF1) Always Below 1 Ω
B107-5 (TR1) - B112-128 (TR1) Always Below 1 Ω
B107-6 (RE1) - B112-125 (RE1) Always Below 1 Ω
B107-1 (AF1+) or B112-127 (AF1+) - Body ground Always 10 kΩ or higher
B107-2 (AF1-) or B112-126 (AF1-) - Body ground Always 10 kΩ or higher
B107-3 (HAF1) or B112-46 (HAF1) - Body ground Always 10 kΩ or higher
B107-5 (TR1) or B112-128 (TR1) - Body ground Always 10 kΩ or higher
B107-6 (RE1) or B112-125 (RE1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351154C11
0.281,1.083 0.729,1.333 0.448,0.25 1.063,1.844 1.688,1.177 false 0.344,1.125 0.729,1.375 0.385,0.25 10 false B107 0.906,1.875 1.25,2.104 0.344,0.229 10 false +B 0.406,0.281 0.75,0.51 0.344,0.229 10 false *a
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (for Sensor 1))


a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B107-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - EFI MAIN NO. 1 RELAY)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - EFI MAIN NO. 1 RELAY)
a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B107-4 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B107-4 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
a.

Replace the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED