Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P1098  Maximum Rail Pressure Exceeded  


DESCRIPTION

For information on the fuel system, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High One of following conditions is met (1 trip detection logic):
·

When rail pressure control is performed according to the fuel quantity control valve, the negative control deviation is the standard value or higher for 2 seconds.

·

When rail pressure control is performed according to the fuel quantity control valve, the rail pressure is the standard value (approximately 175000 kPa) or more for 0.24 seconds.

·

When rail pressure control is performed according to the pressure discharge valve assembly, the negative control deviation is the standard value or higher for 2 seconds.

·

When rail pressure control is performed according to the pressure discharge valve assembly, the rail pressure is the standard value (approximately 215000 kPa) or more for 0.24 seconds.


HINT:

The detection standard value is calculated according to the engine speed and vehicle speed.


·

Fuel quantity control valve (fuel supply pump assembly)

·

Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

·

Pressure discharge valve assembly

·

Open or short in pressure discharge valve assembly circuit

·

ECM


Comes on DTC stored
P1098 Maximum Rail Pressure Exceeded Common rail internal pressure is 215000 kPa or more for 0.3 seconds.
(3 trip detection logic)
·

Pressure discharge valve assembly (jammed closed)

·

Fuel quantity control valve (stuck open) (fuel supply pump assembly)


Comes on DTC stored

Related Data List
DTC No. Data List
P0088
P1098
·

Target Common Rail Pressure

·

Common Rail Pressure

·

Quantity Regulation Valve - Current Value from Common Rail

·

Quantity Regulation Valve - Output Duty Cycle

·

Rail Pressure Control Valve - Current Value from Rail Pressure Valve Control

·

Dutycycle Output of Rail Pressure Control Valve



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the pressure discharge valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0088 and/or P1098 A
DTC P0088 and/or P1098 and other DTCs B


HINT:

If any DTCs other than P0088 and/or P1098 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF PRESSURE CONTROL)

B

2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF PRESSURE CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Pressure Control Valve / Data List / Dutycycle Output of Rail Pressure Control Valve.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Pressure Control Valve
Data List Display
Dutycycle Output of Rail Pressure Control Valve
50004 371 5 132
OK:

The value of "Dutycycle Output of Rail Pressure Control Valve" changes according to the amount "Actuator Test of Pressure Control Valve" is operated.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL)

NG

5.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 371 50,51

d.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Common Rail Pressure is within 10000 kPa of Target Common Rail Pressure when the engine is idling and running at 3000 rpm without load.



Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL SUPPLY PUMP>REMOVAL


b.

Perform the supply pump learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
a.

Replace the pressure discharge valve assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE DISCHARGE VALVE>REMOVAL


b.

Perform the fuel PCV compensation value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END