Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0138  O2 Sensor Circuit High Voltage Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0138 O2 Sensor Circuit High Voltage Bank 1 Sensor 2 The air fuel ratio sensor (for sensor 2) voltage output is 3.2 V or higher for 0.5 seconds.
(3 trip detection logic)
·

Short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the air fuel ratio sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0138 is output A
DTC P0138 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)

B

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-1 (AF2+) - B112-130 (AF2+) Always Below 1 Ω
B133-2 (AF2-) - B112-133 (AF2-) Always Below 1 Ω
B133-3 (HAF2) - B112-17 (HAF2) Always Below 1 Ω
B133-5 (TR2) - B112-131 (TR2) Always Below 1 Ω
B133-6 (RE2) - B112-134 (RE2) Always Below 1 Ω
B133-1 (AF2+) or B112-130 (AF2+) - Body ground Always 10 kΩ or higher
B133-2 (AF2-) or B112-133 (AF2-) - Body ground Always 10 kΩ or higher
B133-3 (HAF2) or B112-17 (HAF2) - Body ground Always 10 kΩ or higher
B133-5 (TR2) or B112-131 (TR2) - Body ground Always 10 kΩ or higher
B133-6 (RE2) or B112-134 (RE2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Check the air fuel ratio sensor for tightness and damages.

OK:

No damage.



Result:
Proceed to
OK
NG



OK

4.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

5.REPAIR OR REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
4.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Replace the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Repair or replace the air fuel ratio sensor (for sensor 2).

i.

Apply compressed air to remove soot stuck to the air fuel ratio sensor. If soot cannot be removed, replace the air fuel ratio sensor.

HINT:

When the air fuel ratio sensor is replaced, perform initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END